background image

 

G.M. International ISM0361-3 

D5212

 - SIL 2 Quadruple Repeater Power Supply 

Front Panel and Features 



Input from Zone 0 (Zone 20) / Division 1, installation in Zone 2 / Division 2. 



Quadruple channels for 2 wires Transmitters or externally powered transmitters. 



0/4-20 mA Input, Output Signals. 



Input and Output short circuit proof. 



Source current Outputs. 



Modbus RTU RS-485 Output. 



Fully programmable operating parameters. 



High Accuracy, µP controlled A/D converter. 



Three port isolation, Input / Output / Supply.  



EMC Compatibility to EN61000-6-2, EN61000-6-4, EN61326-1, EN61326-3-1 for safety system. 



ATEX, IECEx, UL & C-UL, EAC Ex, CCC Certifications 



Type Approval Certificate DNV and KR for maritime applications. 



High Density, four channels per unit. 



Out of range (Burnout) fault detection 



Open-drain alarm output with user-settable trip point 



Simplified installation using standard DIN-Rail and plug-in terminal blocks or customized Termination Boards. 



250 Vrms (Um) max. voltage allowed to the instruments associated with the barrier. 

Terminal block connections 

HAZARDOUS AREA 

SAFE AREA 

+ Output Ch 1 

1

 

- Output Ch 1 

2

 

+ Output Ch 2 

3

 

- Output Ch 2 

4

 

+ Output Ch 3 

5

 

- Output Ch 3 

6

 

+ Power Supply 24 Vdc 

9

 

- Power Supply 24 Vdc 

10

 

Alarm out 

11

 

Alarm out 

12

 

+ Output Ch 4 

7

 

- Output Ch 4 

8

 

+ Input for 2 Wire Transmitters Ch 1 

13

 

- Input for 2 Wire Transmitters Ch 1 

14

 

+ Input for 2 Wire Transmitters Ch 2 

15

 

- Input for 2 Wire Transmitters Ch 2 

16

 

+ Input for 2 Wire Transmitters Ch 3 

17

 

- Input for 2 Wire Transmitters Ch 3 

18

 

+ Input for External Powered Transmitters Ch 1 

21

 

- Input for External Powered Transmitters Ch 1 

22

 

+ Input for External Powered Transmitters Ch 2 

23

 

- Input for External Powered Transmitters Ch 2 

24

 

+ Input for 2 Wire Transmitters Ch 4 

19

 

- Input for 2 Wire Transmitters Ch 4 

20

 

Ordering Information 

 

Model:  

D5212 

4 channels 

Power Bus and DIN-Rail accessories: 
Connector JDFT050 

 

Cover and fix MCHP196 

Terminal block male MOR017 

Terminal block female MOR022 

Operating parameters are programmable from PC by the GM Pocket Portable Adapter PPC5092 via USB serial line and SWC5090 Configurator software. 

13 14 15 16 

17 18 19 20 

21 22 23 24 

4 3 2 1 

8 7 6 5 

12 11 10  9 

Summary of Contents for D5212Q











Reviews: