![background image](http://html.mh-extra.com/html/gmc/ght26/ght26_original-instructions-manual_2235735008.webp)
8
GB
2. Move the Rotating Handle left or right until it ‘clicks’ into position
3. Try moving the Rotating Handle to ensure it is safely locked into position
Preparing 2-stroke mix
Note: This hedge trimmer is powered by a 2-stroke engine that requires a petrol/oil
fuel mixture.
WARNING: ALWAYS use dedicated, fully synthetic 2-stroke oil. DO NOT use regular
engine oil for 2-stroke mix.
1. Use a suitable 2-stroke fuel mixing bottle to measure the required amount of oil,
see mixing chart below
40:1
Unleaded Petrol
1Ltr
2Ltr
3Ltr
4Ltr
Fully Synthetic 2-Stroke Oil
25ml
50ml
75ml
100ml
WARNING: DO NOT pour oil directly into the Fuel Tank (15). The 2-stroke mix needs
to be prepared and thoroughly mixed in a separate container, prior to being poured
into the trimmer.
2. Pour the required amount of 2-stroke oil, followed by unleaded petrol, into the Fuel
Mixing Bottle. Close and shake until thoroughly mixed
Note: 2-stroke mix must not be stored for long-term periods. ONLY mix the amount
required for immediate consumption. Refer to the ‘Storing Fuel’ section for further
information.
Filling with fuel
WARNING: Danger of fire and burn injuries. Take extra care when fuelling this
machine.
WARNING: NEVER fill with fuel whilst the engine is running. Switch off the engine and
wait until it has cooled before refuelling.
WARNING: ONLY refuel the hedge trimmer outdoors, in well-ventilated areas.
WARNING: ALWAYS open the fuel tank carefully to allow potential pressure build-up
inside the tank to release slowly. Never open the fuel tank while the engine is running.
• Always use extreme care when handling fuel. Fuel is highly flammable
• Never attempt to fuel the hedge trimmer if the fuel system components are
damaged or are leaking
• Never attempt to refuel the engine while it is running or still warm; allow it to cool
before fuelling
• Never smoke or light fires near the hedge trimmer or fuels
• Always transport and store fuels in an approved container
• Never place flammable material close to the engine exhaust
• Do not use petrol which contains ethanol or methanol as it may damage the fuel
lines and other engine parts
• Mix only enough fuel for immediate needs. If fuel must be stored longer than 30
days, it should first be treated with a stabiliser or similar product
1. Premix the fuel in a suitable 2-stroke fuel mixing bottle, following the guidelines
under ‘Preparing 2-stroke mix’
2. Place the unit on a secure, flat surface and wipe away any debris from around the
Fuel Cap (16)
3. Unscrew the Fuel Cap and pour the mixture into the tank with the aid of a funnel
Note: Be careful not to spill any of the fuel mixture. If this happens, wipe the spill with
a clean rag.
• In order to avoid risk of fire, start up the engine at least three metres away from the
area where the Fuel Tank has been filled
Operation
WARNING: ALWAYS wear eye protection, adequate respiratory and hearing
protection, as well as suitable gloves, when working with this tool.
WARNING: The blade will continue to move for a few seconds after the engine has
stopped.
Running in the engine
Note: During run-in and cold starts in colder climates, it may be necessary to change
the fuel/oil ratio to 25:1.
• During the first 5 hours of use, run the engine at a moderate speed
• The engine will reach its maximum power output at the end of the run-in period
Switching on and off
1. Move the Ignition Switch (X) into the ‘on’ position by sliding it forwards towards the
Front Handle (4) (Image A)
2. If the engine is being started from cold, move the Choke (7) into the ‘closed’
position before starting (Image B)
3. Press the Primer Bulb (17), roughly 6 times, until the bulb is filled with fuel (Image
C)
4. Pull the Recoil Starter (9) 2-3 times until the engine begins to start
Note: It may be required to pull the Recoil Starter more; depending on the ambient
temperature and the fuel status.
5. Move the Choke into the ‘open’ position, back towards the Rotating Handle (14)
6. Allow the engine to run at idle for 10 seconds to allow trimmer to warm up
• To switch the hedge trimmer off, move the Ignition Switch into the ‘off’ position, by
pushing it towards the rear
• To operate the hedge trimmer, squeeze the Safety Lock to release the Trigger (13)
(Image D)
• Squeeze the Trigger to accelerate the hedge trimmer
Using the hedge trimmer
WARNING: This hedge trimmer is designed for the trimming of hedges, bushes and
shrubs. If it is used for any other purpose not expressly permitted by these operating
instructions, there may be a risk of damage to the hedge trimmer or serious injury to
the user.
WARNING: This product requires the use of both hands to ensure safe operation.
• Inspect the area to be cut before starting. Remove any objects or debris that could
be thrown, jammed or become entangled in the blades
• Allow the cutting blades to reach full speed before commencing the cut
• When cutting always move in a forward direction and never backwards
• Never work towards bystanders or solid objects such as walls, trees or vehicles
• If during cutting the blade stalls, stop the hedge trimmer immediately by switching
the Ignition Switch (X) to ‘off’ before investigating the cause
• Remove any jammed debris from the blades and examine them for any damage
before re-commencing cutting. Always replace any damaged blades.
• The hedge trimmer can be used for trimming soft and new growth on hedges,
shrubs and bushes.
829828_Z1MANPRO1.indd 8
08/11/2016 10:56