background image

Grinder adjustments

During the life of the grinder some adjustments are
required to maintain a safe working environment. Please
ensure the following: 

• 

Always adjust the eye shields to the most 
comfortable and most effective angle to suit the task
being performed.

• 

As the wheels wear, the top eye shield bracket must be
adjusted to ensure the gap between the bracket and the
wheel does not exceed 6mm.

• 

As the wheels wear the tool rests must also be adjusted
so there in never a gap of greater than 1.5mm between
the wheel and the edge of the tool rest.

Maintenance

Prior to any maintenance ensure the power has been
turned off and the plug is removed so that the grinder is
fully disconnected from the 240V supply.

Lubrication

1. All models use pre-lubricated sealed ball bearings for

the motor and do not require lubrication. 

2. If the wheels do not rotate freely, the bearings should

be replaced by an authorised service centre.

3. On the wet and dry grinder/sharpener, the lubrication of

the worm drive should be checked after each 50 hours
of operation by an authorised service centre.

Cleaning

1. Keep the outside of the grinder clean by brushing grinding

dust and dirt away from all areas where the dust tends to
build up.

2. Wipe the guards and grinder with a soft damp cloth. A

mild detergent can also be used.

3. Wipe the eye shields with a soft damp cloth, making 

sure not to scratch the surface. A mild detergent can also
be used.

Caution.

Never use caustic agents, petrol based cleaners,

alcohol or any other cleaning agents. Do not wet down 
the grinder.

General inspection

1. Regularly check that all the fixing screws are tight. They

may vibrate loose over time. 

Repairs

1. Only an authorised service centre should replace the

cordset or carry out other repairs. If the cordset is
damaged or worn, have it repaired or replaced by an
authorised service centre.

12

Summary of Contents for BG125A














Reviews: