place it as closer to center position as possible. Be sure the steering trim on the transmitter
at the neutral position.
Trim Operation And Maximum Trav
Changing the trim can effect the overall settings, when adjustments are made with the trims,
please recheck your installation for maximum servo travel (Steering EPA right side and left
side).
When Trim movement goes to extremes
That means if you make a lot of trim movement to get a servo to the neutral position, please
reposition the servo horn or servo saver on the servo and inspect your linkage installation.
15 94001 GM-Racing XG-6i Race Spec Instructions
English
SERVICE AND REPAIR
In problem cases, or for questions and repairs, please contact:
GRAUPNER-Service, Henriettenstrasse 94-96, D-73230 Kirchheim/Teck,
Tel. +49/1805/472876
Gastrimmung (TH.TRIM)
Throttle neutral adjustments can be made by moving the throttle trim to the left or the right.
Racers Tip
When using a electronic speed control, please set the throttle trim to neutral and make adjust-
ments to the speed control. On a gas powered model, set the trim to neutral and adjust the
linkage to the point where carburetor is fully closed in accordance with the engine instruction
manual.
Trim Operation and Travel
Trim adjustments will effect the overall servo travel, so please check the (backward)
movement after the adjustment
When trim movement is goes to extremes
That means if you make a lot of the trim movement to get the servo to the neutral position,
please recenter the servo horn closer to the neutral position and inspect your throttle
linkage.
TECHN. DATA TRANSMITTER:
RECEIVER:
Frequency............................. 2.4 Ghz DSSS....................... 2.4 Ghz DSSS
Power Requirement................8.7 – 12 V DC........................ 4.8 - 5.6V DC
Channels...............................3.......................................... 3
Current Drain........................ ca. 300 mA (9,6V).................. ca. 14 mA
ST.D/R range......................... 0% - 120%
Temperature (working)...........0° ~ +70° C
Spare parts:
94000.1
Receiver 2,4Ghz for XG-6i
94000.2
Binding-Plug for XG-6i Receiver
94000.3
Receiver - Antenna 2,4Ghz
94000.6
Antenna 2,4Ghz für XG-6i Transmitter
94000.10
Micro Receiver 2,4Ghz for XG-6i
LIABILITY FOR PRINTING ERRORS EXCLUDED!
WE RESERVE THE RIGHT TO INTRODUCE MODIFICATIONS!
4. SERVOREVERSE
(REV)
This function reverses the direction of operation of the servos
related to transmitter steering, throttle, and channel 3 operation.
1. Press “ENTER” to see FUNCTION MENU.
2. Press “+” or “-“ to choose REVERSE, and press “ENTER”
to
enter REVERSE adjusting interface.
3. Press “ENTER” to choose each Channel.
4. Press “+” to increase and “-” to choose “REV” or “NOR”.
5. Press “EXIT”to save your setting and leave REVERSE
interface, and back to the function menu interface.
Note:
However, when the position set by trim or sub trim shifts from the center, the center
becomes the opposite side.
TERMS: ST-STEERING, TH-THROTTLE,AUX-AUXILLIARY
94001 GM-Racing XG-6i Race Spec Instructions 04
English
2. STEERING RANGE (ST.D/R)
D/R is used to change the action range of steering servo when turning the steering wheel.
Increasing D/R will make the steering wheel action more sensitive. --D/R adjusting value
range: 0~120%, POS0 default value is 100%,POS1 default value is 70%. -- Press the ST.D/R
dial to select POS0 or POS1, and the value will display in the LCD when it is on the main
screen.
1. Press “ENTER” to see FUNCTION MENU.
2. Press “+” or “-“ to choose D/R, and press “ENTER” to enter D/R adjusting inter-
face.
3. Press “+” to increase and “-” to decrease D/R value.
4. Press “EXIT” to save your setting and leave D/R interface, and back to the function
menu
interface.
TERMS: POS-POSITION
3. SUB-TRIM
(S_TRIM)
Use this function to adjust the neutral position of the steering
and throttle servos. SUB TRIM adjusting value range: -100 -
100. Default is 0.
1. Press “ENTER” to see FUNCTION MENU.
2. Press “+” or “-“ to choose TRIM, and press “ENTER”
to enter SUB TRIM adjusting interface.
3. Press “+” to increase and “-” to decrease SUB TRIM
value.
4. Press “EXIT”to save your setting and leave SUB TRIM interface, and back to the
function menu interface.
TERMS: ST-STEERING, TH-THROTTLE
94001-eng.indd Druckbogen 5 von 10 - Seiten (16, 5)
94001-eng.indd Druckbogen 5 von 10 - Seiten (16, 5)
19.01.2009 08:02:47
19.01.2009 08:02:47
