07 94001 GM-Racing XG-6i Race Spec Instructions
English
7. ANIT LOCK BRAKE SYSTEM (ABS)
When the brakes are applied while cornering with a 4 Wheel Drive or other type of vehicle,
understeer may occur. The generation of understeer can be eliminated and corners can
be smoothly cleared by using this function. When the brakes are applied, the throttle servo
will pulse intermittently. This will have the same effect as pumping the brakes in a full size
car. The brake return amount, pulse cycle, and brake duty can be adjusted. The region over
which the ABS is effective can be set according to the steering operation.
1. Press “ENTER” to see FUNCTION MENU.
2. Use the +/- Keys to select the ABS function and press ENTER.
3. Press ENTER to select PT item. Use +/- to change the value. Range: 0%~100%..
4. Press ENTER to select WD item. Use +/- to change the value. Range: 0%~100%.
5. Press ENTER to select CY item. Use +/- to change the value. Range: 0~30.
6. Press ENTER to select DL item. Use +/- to change the value. Range: 0~100.
7. Press ENTER to select DT item. Use +/- to change the value. Range: 0~100%.
8. Press ENTER to select SM item. Use +/- to change the value. Range: 0~100%. If this
value is 0, disable the steering mix.
9. Press ENTER to select MODE item. Use +/- to change INH, TH, AUX or
TH
&
AUX.
10. Press EXIT twice to save and return to FUNCTION MENU, press EXIT again to return
to the Main Screen.
TERMS:
PT-Operation: Throttle Trigger point
WD-Brake return amount: Sets the rate at which the servo returns versus trigger
operation for brake release. When set to 0%, the ABS function is not performed.
CY-Cycle speed: The smaller of the set value, the faster the pulse cycle.
DL-Delay amount: Sets the delay from brake operation to ABS operation. When set to 0%,
the ABS function is activated without any delay.
SM-Steering Mix
DT-Cycle duty ratio: Sets the proportion of the time of the brakes are applied and the time of
the brakes are released by pulse operation.
MODE:If it is selected to INH, the function disable. If it is selected to TH, the ABS function for
THROTTLE brake. When it is selected to AUX, the ABS function for the AUX channel.
If it is selected to TH&AUX, the ABS function for both THROTTLE and AUX.
NOTE: the AUX and TH&AUX can select only the Brake MIX set to ON.
94001 GM-Racing XG-6i Race Spec Instructions 12
English
15. FAILSAFE (F/S)
If the RF signal loss, it should occur the receiver adjust the Steering or Throttle or both
to a preset value. The servo value of Steering channel and Throttle channel in the fail
status can be set through fail safe function.
1. Press “ENTER” to see FUNCTION MENU.
2. Use the +/- Keys to select the F/S function and press ENTER.
3. Press ENTER to select a item.
4. Use the +/- Key to change the value.
5. Press EXIT twice to save and return to FUNCTION MENU, press EXIT again
to return to the Main Screen.
TERMS:
ST -- To set the servo value of Steering channel. Range -120% to +120%. Default: 0%.
16. NEUTRAL
This function can calibrate the neutral of the STEERING wheel or THROTTLE trigger.
1. Press “ENTER” to see FUNCTION MENU.
2. Use the +/- Keys to select the NEUTRAL function and press ENTER.
3. Use the +/- Keys to select YES.
4. Press ENTER to calibrate the neutral.
5. Press EXIT twice to save and return to FUNCTION MENU, press EXIT again to
return to the Main Screen.
Note:
Don‘t move the STEERING wheel or THROTTLE trigger in the calibrate procedure.
94001-eng.indd Druckbogen 8 von 10 - Seiten (8, 13)
94001-eng.indd Druckbogen 8 von 10 - Seiten (8, 13)
19.01.2009 08:02:48
19.01.2009 08:02:48
