Glow-worm Envirosorb 10 Instructions For Use Manual Download Page 6

www.glow-worm.co.uk

6

1.2 Testing and Certification

This appliance is certificated for performance and safety in use. 
It is important that no alteration is made to the appliance unless 

approved, in writing, by Glow-worm.
Any alteration not approved by Glow-worm, could invalidate 

the certification, appliance warranty and may also infringe the 

current issue of the statutory requirements.

1.3 CE Mark

The CE mark on this appliance shows compliance with:
1.   Directive 97/23/EEC on pressure equipment
2.   Directive 73/23/EEC on the harmonisation of the Laws of the 

Member States relating to electrical equipment designed for use 

within certain voltage limits.
3.   Directive 89/336/EEC on the approximation of the Laws of 

the Member States relating to electromagnetic compatibility.

1.4 General Note

Servicing/maintenance should be carried out by a competent 

person in accordance with the rules in force in the countries of 

destination.

1.5 Servicing

This appliance should be serviced regularly to optimise its 

safety, efficiency and performance.  
To ensure the continued efficient and safe operation of the 

appliance it is recommended that it is checked and serviced at 

regular intervals. The frequency of servicing will depend upon 

the site conditions and usage, but in general, once a year should 

be enough.
To obtain service, please call your installer or Glow-worm’s own 

service organisation using the telephone number on the inside 

front cover of this booklet.

1.6 Spare Parts

REMEMBER:

 When replacing a part on this appliance, use 

only spare parts that you can be assured conform to the 

safety and performance specification that we require. Do not 

use reconditioned or copy parts that have not been clearly 

authorised by Glow-worm.
If replacement parts are required contact Glow-worm’s own 

service organisation using the telephone number on the 

inside front cover of this booklet.
Please quote the name and model of the appliance. The 

name and model badge is on the outer case above the 

hydraulic connections.
If in doubt seek advice from Glow-worm’s own service 

organisation using the telephone number on the inside front 

cover of this booklet.

1  Your safety

Summary of Contents for Envirosorb 10

























Reviews: