background image

3

2. Declaration of Conformity            

Construction in accordance with the following safety standards:

EN 61010-1
EN 61010-2-10

Construction in accordance with the following EMC standards:

EN 61326-1/ FCC Part 15 Subpart B/ IECS 001

Associated EU guidelines:

EMC guidelines: 2004/108/EC
Centrifuge guidelines: 
This ISM device complies with Canadian ICES-001.
Cet appareil ISM est conforme à la norme NMB-001 du Canada.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s 
authority to operate the equipment. 

NOTE: 

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of 

the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment 
is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not 
installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. 
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to 
correct the interference at his own expense. 

3. Required Operating Conditions        

3.1 Basic Operational Conditions

• GCM-24: Single-phase, 220V-240V, 50Hz/60Hz, 5A; 110V-120V, 50Hz/60Hz, 5A 

    GCM-R-24: Single-phase, 220V-240V, 50Hz/60Hz, 10A; 110V-120V, 50Hz/60Hz, 10A

• Ambient temperature: 2ºC~40ºC 

• Relative humidity: ≤80%

• No vibration and airflow around the centrifuge

• No static, explosive or corrosive gases around the centrifuge

3.2 Transport and Storage Conditions 

• Storage temperature: -40ºC-55ºC

• Relative humidity: ≤93%, non-condensing

Summary of Contents for GCM-24























Reviews: