TANK DRAINING
1. Turn the power off on the machine.
2. With the squeegee and brush head in their "up" position,
transport machine to approved area for draining tank(s).
DRAINING THE RECOVERY (DIRTY) TANK
1. Remove the drain hose from the holder, and place the
drain hose over the floor drain. Twist off the drain hose
plug to begin the draining process. In order to
completely empty the recovery tank, hinge open the
recovery tank and let it rest on the support stand.
2. Clean the recovery tank after every use. Use a fresh
water hose to rinse out the recovery tank. Be careful not
to spray water into the float shut-off mechanism.
3. Replace the drain hose plug tightly as soon as you are
done draining the tank.
DRAINING THE SOLUTION (CLEAN) TANK
1. Pull down on the clear tube (back left of the machine) to
remove it from the hose barb. This will allow the solution
to flow freely into a bucket or floor drain.
2. Rinse the solution tank with clean water after every use.
This will help prevent chemical buildup and clogging of
the solution lines.
3. With clean water in solution tank, turn machine power
on, solution switch "on" and pull the operating triggers.
This will allow the clean water to flush through and clean
the solution plumbing.
4. Once tank is rinsed, flushed and drained, reconnect the
clear tube to the hose barb. Be sure the tube is pushed
all the way up on the hose barb.
BATTERY CHARGING
MACHINE OPERATION CONTINUED
CAUTION
The brush motors are circuit breaker
protected to protect them from damage. If a
breaker trips, it can't be reset immediately. You
must first determine what caused the breaker to
trip, and allow the motor to cool down before you
can reset the breaker. The breakers are located on
the back panel of the control housing.
7
!
WARNING
DO NOT lift/flip open recovery tank fully when
filled, may cause spills
!
CAUTION
Any time scrubbing is completed, or when
refilling solution tank, the recovery tank should be
drained and cleaned.
!
CAUTION
If you are storing the machine for any period of time,
always leave the clear recovery tank lid off the tank so
the tank can dry completely and smell fresh.
!
CAUTION
Any time scrubbing operation is completed,
the solution tank should be drained and cleaned.
!
WARNING
If the recovery tank is not drained when the
solution tank has been refilled, foam or water may
enter the float shut-off mechanism and cause
damage to the vacuum motor.
!
WARNING
Use only approved chargers with the following
specifications:
• Automatic shut off circuit
• Deep cycle charging
• Output current of 10 - 20 amps
• Output voltage of 24 volts
!
CAUTION
For the best machine performance, keep
batteries charged at all times. Do not let them sit
in a discharged condition.
!
WARNING
DO NOT place battery charger on wet surface or in
a puddle when operating charger.
!
WARNING
Batteries are dangerous! Batteries emit
hydrogen gas and an explosion or fire can result.
Keep sparks and fire away from batteries at all
times. When charging the machine, make sure the
battery compartment is left open.
!
Summary of Contents for 261123
