background image

 

244280                                                           

www.globalindustrial.com

                                                    5 

 

3.3 Key Functions 

 

 

 

Press to enter number in counting and checking weighing modes 
and calibration 

 

Press to clear the input number or accumulated value                                                                                                                                                                                                                                                                             

 

Press to tare the weight when reading is stable, tare range: 
100%FS 
Press to confirm the operation or entered data 

 

Press to set the zero point after the scale is stable, zero range

power-on zero point±5%FS 

 

Press to add the value to the accumulation memory 
Press and hold to display the accumulated total value 

 

Press to switch the measuring unit between kg, g, lb and oz 

 

Press to output data via RS232 port 

 

Press to enter check weighing mode, set Hi and Lo value 

 

Press to enter % weighing mode 
In counting mode, press to display unit weight(g/pcs), total 
weight(kg) or count(pcs) 

 

Press to enter into counting mode 
Press to exit the current working mode and return to normal 
weighing mode 

Summary of Contents for 244280



















Reviews: