manualshive.com logo in svg

Global Hobby Wattage P-51 Reno Racer EP, Instructions For Final Assembly, Page: 32 / 44

Share
Download
Global Hobby Wattage P-51 Reno Racer EP Instructions For Final Assembly Download Page 32

32

Need help or have any questions?  Call us at 1-714-963-0329 or send us an email to [email protected]

❑

Attach the servo horn to the Z-Bends, then attach the

servo horn to the servo, making sure that it's centered.

☞

You will have to enlarge the holes in the servo arms using

a 1/16" drill bit so that you can attach the pushrods.

❑

Install and tighten the servo horn retaining screw, provided

with your servo, to secure the servo horn into place.

❑

Kwik Bond 5 Minute Epoxy

❑

Kwik Bond Thin C/A

❑

Ruler

❑

Pencil

❑

220 Grit Sandpaper w/Sanding Block

YOU'LL NEED THE FOLLOWING PARTS:

❑

(2) Prebent Main Landing Gear Wires

❑

(2) Plastic Main Gear Wheels

❑

(2) Plastic Main Gear Wheel Retainers

SECTION 12:  MAIN LANDING GEAR INSTALLATION

❑

(2) Rubber Bands

❑

(2) Nylon Main Landing Gear Mounts

YOU'LL NEED THE FOLLOWING TOOLS AND SUPPLIES:

❑

Paper Towels

❑

Rubbing Alcohol

❑

NHP Epoxy Mixing Sticks

❑

NHP Epoxy Mixing Cups

Step 1:  Installing the Landing Gear Wires

❑

Carefully push the prebent loop in each landing gear wire

through the molded slot in the two nylon landing gear mounts.

☞

Make sure the prebent loop is pushed into the slot as far

as possible as shown.

If you plan on strictly flying your P-51 Reno Racer off of grass we suggest 

not

 installing the main gear assembly.  The

main gear is not necessary for landing on grass and will only cause complication.

☞

If you ever want to remove the landing gear after it has been glued to the wing, you can simply squeeze the prebent

loop together and pull the wire from the nylon mount.

Summary of Contents for Wattage P-51 Reno Racer EP













































Reviews:

No comments