background image

GlideTrak Assembly & Set Up

 

22 
 

 

 

Reset the Ratchets after each workout 

 

76.

  After each workout session reset the Ratchets on the Front 

Straps so they are ready for your next session.   

77.

  To do this, stabilize the Ratchet and press the Center Lever to 

release the Ratchet.  

(See photo 39)

 

 

Photo 39

   

Closed ratchet. 

Arrow indicates where to 
depress center lever 

 

Photo 40    Reaset Ratchets:  

Press Center Lever and open 
ratchet fully.  Pull strap tight

 

78.

  While still depressing the Center Lever, open the Ratchet fully. You will feel the mechanism release 

slightly.  

(Photo 40) 

79.

  Pull the taught end of the Strap away from the Ratchet, removing any slack and straightening the Strap.  

(Photo 40) 

 

 

80.

  Once your GlideTrak session is complete, 

make 

note of the settings for your Seat Assembly 

and the hook settings

 

for your front and rear 

Straps. 

The Strap Hooks and Seat Assembly settings will 

likely remain the same and will not need adjusting 

for your subsequent workouts.   

You are done with your GlideTrak  

exercise session! 

 

 

Summary of Contents for Indoor Trainer





























Reviews: