background image

Page 24

INSTALLATION

INST

ALL

A

TION

Connection/Supply Arrangements

The  position  of  the  pipework  connections  is 
shown opposite. Dimensions are shown in the 
Technical Data section.

All  the  connections  are  also  labelled  on  the 
appliance.  It is essential that the pipework is 
connected to the correct connection.

1  -  Safety/open  vent  connection  -  22mm 

copper tube

2  -  Cold feed/expansion connection - 15mm 

copper tube

3  -  Solar  expansion  vessel  connection  - 

15mm compression

4  -  Solar  return  connection  (to  collector) 

- 22mm compression

5  -  Solar  flow  connection  (from  collector 

- 15mm compression

6  -  Heating  flow  connection  -  22mm 

compression

7  -  Primary  return  connection  (to  boiler) 

- 22mm compression

8  -  Heating  return  connection  -  22mm 

copper tube

9  -  Solar coil drain connection - Rc 1/2
10 -  Primary  flow  connection  (from  boiler) 

- 22mm copper tube

11 -  Thermal store drain connection - Rc 1/2
12 -  Domestic mains cold water connection 

- 22mm compression

13 -  Domestic hot water connection - 22mm 

compression

All factory made joints should be checked  
after  installation  in  case  they  have  been 
loosened during transit.

All  the  fittings  for  the  feed  and  expansion 
cistern should be installed to meet the Water 
Regulations, in a position to suit the particular 
site  location  and  the  cistern  fitted  on  its 
supports/base.

The cold feed/expansion and safety/open vent 
pipework provided should be installed between 
the  appliance  and  the  feed  and  expansion 
cistern.

Figure 1.14

4

5

2

1

3

10

11
12

13

6

9

8

7

Summary of Contents for BMA 215 OV-SOL

















































Reviews: