GLAZING VISION Xvent Operation And Maintenance Manual Download Page 5

 

405-OM-UK-001 v1.0 

 09 Jul 2020 

 

Need assistance? +44 (0)1379 658300 [email protected] 

Page 5 of 18 

 

Do not place anything on, or cause obstruction to, the moving sections of the product as this may cause damage to the 
mechanisms/product and/or prevent the unit from opening/closing. 

 

Do not allow unauthorised persons (e.g. children) to operate the product as this may lead to personal injury or damage to 
the product. Do not leave children or pets unsupervised near the product 

 it may open/close unexpectedly (e.g. due to the 

rain sensor activating) and cause injury. 

 

Do not pull on the cables where they exit the product. Doing so may loosen connections, result in damage to the product 
and/or create the need for a repair visit. 

 

Do not leave the product open in the rain, this could damage the control board and/or mechanisms. If required, a rain 
sensor can be specified at the time of order. 

 

Should any cables or electrical components break or become damaged, have them repaired or replaced immediately. 
Deteriorated insulation of electrical parts or overloading may cause an electric shock or fire. 

 
For more information or assistance please contact Glazing Vision. 

 

 

Summary of Contents for Xvent



















Reviews: