background image

    

Insert the Spinner Plate (ITEM 1) onto the 
vertical shaft of the Gear Box and Axle 
Assembly  (ITEM 2).

Insert the M4 x 20mm Screw (ITEM 3) to 

secure the Spinner Plate in position.

ITEM 1
ITEM 3

ITEM 2

A.

    

B.

ITEM 4

Take the Wheel Assembly Frame 

(ITEM 4 - 2 off) and locate on 

each end of the Gear Box and 

Axle Assembly (ITEM 2). Ensure 

Axle Bush (ITEM 5 - 2 off) are in 

position.

IMPORTANT: Ensure the hole in the 

Gearbox and Axle Assembly is 

positioned on the right hand side.

Attach one end of the Frame 

Brace (ITEM 6 - 2 off) to the 

Hopper Frame (ITEM 7), in the 

orientation shown, using M6 x 

35mm Bolt (ITEM 8 - 2 off) and M6 

Lock Nut (ITEM 9 - 2 off).

Secure the Connector Rod (ITEM 

10) in position by inserting M6 x 

35mm Bolt (ITEM 8 - 2 off) through 

each Wheel Assembly Frame 

(ITEM 4) and Frame Brace (ITEM 

6).

Insert the M6 x 60mm Bolt (ITEM 

32 - 2 off) through each Wheel 

Assembly Frame (ITEM 4) and 

Hopper Frame (ITEM 7). Secure in 

position using M6 Lock Nut (ITEM 

9 - 2 off) - Do not fully tighten.

ITEM 2

IMPORTANT HOLE 

ITEM 6

ITEM 7

ITEM 8

ITEM 9

ITEM 10

ITEM 8

ITEM 5

ITEM 32

Summary of Contents for ICEMASTER 50









Reviews: