Gladiator 10.0K Product Manual Download Page 2

 

INTRODUCTION

 

 
Thank you and congratulations for choosing GLADIATOR Car Audio for your amplification 
needs. GLADIATOR amplifiers have been significantly improved throughout the year to 
assure quality and reliability. The latest in technology has been incorporated into every 
GLADIATOR product providing you with incredible power and unparalleled sound quality. 
Our simple yet highly developed circuitry, contributes to low distortion and the ultimate in 
efficiency. This is why we are sure that your new GLADIATOR amplifier will provide you 
with a sound experience you will enjoy years to come. 
 
 
 
 

Mounting 

Appropriate mounting is very important for prolonged life expectancy of any amplifier. Select 
a location that allows enough space so sufficient airflow is maintainable and a location that 
provides protection from moisture. Keep in mind that an amplifier should never be mounted 
upside down. 
Upside down mounting will compromise heat dissipation through the heatsink and could 
engage the thermal protection circuit. 
Excessive heat will shorten your amplifier life. To maximize heat dissipation, be sure to 
leave at least 2.5 inches of clearance around the amplifier. If space is of the essence and 
the amplifier must be mounted in an enclosed or restricted area, small 3 inches fan should 
be used in correspondence with a duct so the heat can flow past the heatsink. 
 
 
Try to avoid mounting any amplifier on a subwoofer enclosure, as extended exposure to 
vibration may cause malfunction of the amplifier. 
 
To avoid scratching your new GLADIATOR amplifier, pre-drill the mounting holes with either 
a 3mm or 9/64

” diameter drill bit and use the screws supplied in the accessory kit. Be sure 

to investigate your mounting area thoroughly to avoid electrical wires, vacuum lines and 
brake or fuel lines. 
 

HOOK ME UP 

 
The quality of installation will affect the performance and reliability of your GLADIATOR 
amplifier. For maximum performance we recommend you have new GLADIATOR amplifier 
installed by an authorized GLADIATOR dealer. Our highly skilled dealers have a vast 
knowledge of our produce and their installation techniques are necessary to unleash the 
high performance capabilities of your amplifier. 
 
If you decide to connect the amplifier by yourself. It is important that you read this manual 
carefully and throughout before starting. Once you have finished reading and you still have 
question regarding installation, we recommend you see your local GLADIATOR dealer.  
 
 
 
 
 
 

 

Summary of Contents for 10.0K













Reviews: