background image

GIRA

 

Info

 

 

Hand-held radio transmitter 

Installation Instructions 

 

 

Hand-held radio transmitter 

15/01 

Page: 2 of 10 

 
 

The lightscape data are stored in the radio re-
ceiver. They can be recalled with a hand-held or 
wall-mounted transmitter. 
The master key   can be used for switching or 
dimming of a lightscape (see master key ope-
ration). 

 

 

!

 

Start-up 

 

Batteries 

 
The hand-held radio transmitter requires 4 
Alkaline Micro Batteries (LR 03) for operation (not 
included in the scope of supply). 
 

Risk and disposal instructions 
Attention: 
Keep batteries away from children. 
Remove empty batteries immediately and 
discard without polluting the environment. 
Replace batteries only by identical or equi-
valent types.

 

 

 

+

+

+

+

 

Inserting the batteries: 

1. Press to open the battery case   at the back of 

the enclosure. 

2. Insert the batteries as shown in fig.   paying 

attention to correct polarity. 

3. Close the battery case. 
 
 

Important 

Replace the batteries when all 3 LEDs start 
flashing for abt. 4 seconds after a key has been 
depressed. 

General 

 
The maximum duration of a transmission is limited 
to 12 seconds even if any of the keys is kept de-
pressed longer. 
 

No

 data telegram is transmitted if 

several keys 

are depressed at the time. 

 
Please hand these instructions over to your 
customer after the installation.

 

 

Summary of Contents for 0523 00











Reviews: