MAINTENANCE
980146 02/19/04
4-3
4. VACUUM
MOTOR
(Refer to vacuum group in the parts section of
manual).
ONLY QUALIFIED MAINTENANCE PERSONNEL
ARE TO PERFORM THE FOLLOWING REPAIRS.
VACUUM MOTOR REPLACEMENT
1.
Turn off all switches and unplug machine.
2.
Drain tanks and remove all chemicals and
accessories.
3.
Unlatch two front latches and hinge tanks back.
4.
Locate the vacuum motor wires and disconnect
at the connector.
5.
Remove the vacuum motor.
6.
Reverse process to install.
Vacuum Motor Carbon Brushes Replacement (Windsor)
WARNING:
The green
ground wire must be
attached for safe
operation. See wiring
diagram.
End Cap
Carbon
Brushes
If armature commutator is grooved, extremely pitted or not
concentric, the motor will need to be replaced or sent to a
qualified service center.
Important:
These brushes wear quicker as the length shortens due to
increased heat. Spring inside brush housing will damage
motor if brushes are allowed to wear away completely.
Periodically check the length of the carbon brushes. Replace
both carbon brushes when either is less than 3/8" (9.5mm)
long.
3
8
[9.5mm]
Important:
These brushes wear quicker as the length shortens due to
increased heat. Spring inside brush housing will damage
motor if brushes are allowed to wear away completely.
Periodically check the length of the carbon brushes. Replace
both carbon brushes when either is less than 3/8" (9.5mm)
long.
3/8 (9.5mm)
Vacuum Motor Carbon Brushes Replacement (Ametek)
Note:
When replacing carbon brushes loosen wire terminal
BEFORE
removing screws on bracket.
Note:
Place
stop in
groove.
Wire
Terminal
WARNING:
The green
ground wire must be
attached for safe operation.
See wiring diagram.
End Cap
Carbon
Brushes
Wire Terminal
If armature commutator is grooved, extremely pitted or not
concentric, the motor will need to be replaced or sent to a
qualified service center.
Summary of Contents for Century 400
