background image

2.Safety Instructions

.5.

2.2 General Safety Instructions

WARNING: 

Electrical installations must be done in accordance with the local and national 
electrical safety standards

CAUTION: 

CAUTION, RISK OF ELECTRIC SHOCK symbol indicates important safety 
instructions, which if not correctly followed, could result in electric shock.

CAUTION: 

CAUTION, HOT SURFACE symbol indicates safety instructions, which if not 
correctly followed, could result in burns.

NOTE: 

NOTE symbol indicates important safety instructions, which if not correctly 
followed, could result in some damage or the destruction of the inverter.

2.1 Safety Symbols

Safety symbols used in this manual, which highlight potential safety risks and important 

safety information, are listed as follows:

WARNING: 

WARNING symbol indicates important safety instructions, which if not 
correctly followed, could result in serious injury or death.

Improper use may result in potential electric shock hazards or burns. This manual 

contains important instructions that should be followed during installation and 

maintenance. Please read these instructions carefully before use and keep them for 

future reference.

WARNING:

Please don’t connect PV array po) or negative(-) to the ground, it could 

cause serious damage to the inverter.

.4.

1.2 Packaging

When you receive the inverter, please check if all the parts listed below are included:

 1. Introduction

Part NO.

1

 Description

PV grid tie inverter

2

Wall mounting bracket 

3

Locking screws 

5

 AC connector

6

DC connectors

Manual

7

 Number

1

1

2

1

4 pairs(2 for Solis-6K)

1

Table

 1.1 

Material list

4

5

6

PV Grid Tie Inverter

Installation and Operation Manual

 2014, Ningbo Ginlong Technologies Co., Ltd.

C

Ver 2.5

Solis Three Phase Inverter

Summary of Contents for Solis-10K



















Reviews: