background image

 

Operator

s Manual

 

MO080-IT 

12/09/2017 

Rev.3 

Page 7 of 20 

 

1.5  Warranty Certificate

 

1.

 

The Product is covered by an 18-month warranty, including electrical parts 

2.

 

The warranty begins on the date of product shipment from the GIMA warehouse to the buyer. 

3.

 

In case of disputes, the date indicated on the “transport document” attached to the goods shall be deemed 
valid. 

4.

 

The  warranty  only  covers  the  sending  of  Product  spare  parts  to  the  buyer  or,  in  the  event  of  GIMA 

considering the replacement of spare parts not  feasible, the replacement of the entire product, after fabrication 
faults have been properly ascertained at the undisputable judgement of GIMA . The warranty does not therefore 
cover any other costs or expenses (including, by way of example but without limitation, labour costs, packaging 
costs and transport costs, etc.). 
5.

 

The guarantee does not include the components subject to normal wear, such as halogen bulbs, LEDs, fuses, 

relays, ball bearings, etc.) 
6.

 

The warranty does not cover: 

-

 

malfunctions due to failure to comply with all instruction manuals; 

-

 

malfunctions due to installation and/or maintenance errors; 

-

 

malfunctions or faults caused by carelessness, negligence, incorrect use or other causes not attributable to 
GIMA; 

-

 

malfunctions or faults due to the fact that the electrical system of the premises where the device is installed 
is not in compliance with CEI 64-8 standards (standards for electrical systems in premises used for medical 
purposes) and similar standards. 

7.

 

GIMA GIMA shall repay direct damages suffered by the buyer and which are documented as attributable to 

its product, caused within the warranty period, for an amount not above 40% of the net value of the product as 
indicated on the buyer’s invoice. GIMA’s liability is expressly ruled out for indirect damages or consequential 
damages (including cases of the lamp not being used) deriving from the supply. 
8.

 

This warranty certificate replaces legal warranties for faults and non-conformities and rules out any other 

possible liability of GIMA originating from the supplied products. 
9.

 

The payment of any damages to persons or things due to product malfunction or faults shall be limited to 

the maximum amount of GIMA’s insurance coverage for civil liability. 
10.

 

The warranty shall be automatically invalidated in the event of: 

-

 

the Product having been tampered with or modified by the buyer or third parties; 

-

 

the  Product  having  been  repaired  by  the  buyer  or  third  parties,  without  following  the  instructions  in  the 

instruction manuals; 

 

the Product serial number having been cancelled, defaced or removed; 

 

the buyer not being up to date with payments. 

11.

 

For jobs to be done under warranty, the buyer shall contact GIMA only. 

12.

 

The component parts replaced under warranty must only be returned to  GIMA, if so requested by GIMA, 

carriage free and suitably packed. 
13.

 

In case of failure to return a part requested by GIMA, the cost of the component part will be charged. 

14.

 

GIMA cannot accept returns from end users or in any case from parties other than the buyer. 

15.

 

Products  returned  to  GIMA  must  be  complete  with  documentation  authorising  such  return  and  another 

document describing the malfunction. 
16.

 

For everything not indicated on this warranty certificate, reference shall be made to the laws of Italy 

17.

 

For all disputes deriving from or related to  the orders to which this warranty certificate applies and which 

cannot be amicably settled between the parties, the only competent law court shall be that of Milan. 

Summary of Contents for PRIMALED SO

































Reviews: