manualshive.com logo in svg

Gill AGX M4 POLE VAULT, Manual

Share
Download
Gill AGX M4 POLE VAULT Manual Download Page 14

1

3

2

2

4

RAISING THE UPRIGHT

4x Adults required.

Make sure to have all tools and hardware close 
by before starting.

Make sure there is nothing on the leveling plate.

Make sure the hinge pins are in place.

Slowly raise the upright. Secure the stem plate to 
the leveling plate with provided hardware.

Tip: It may be helpful to have one person pull with a 
rope while the other three push. 

To do this, move the carriage to about half way along 
the upright and 

engage the brake (red handle)

. With 

a rope, make a loose loop around the upright above 
the the carriage and make a tight knot.

After the upright is vertical and 

bolted down

, release 

the brake and lower the carriage. The loop should 
lower with the carriage so that the knot can be undone. 

#

    Part # 

Description

Qty.

1

HDWE01294

5/8"-11 X 1-3/4" HEX HEAD CAP SCREW; GR8; ARMOR COAT

4

2

HDWE05023

5/8" FLAT WASHER; SS

8

3

HDWE04010

5/8" SPLIT RING LOCK WASHER; SS

4

4

HDWE03102

5/8"-11 THIN HEX NUT; ARMOR COAT

4

139

3060T47

4

140

M1291

3/8"-16 Nylock hex nut, standard height

8

141

HDWE050040

E0

3/8" Flatwasher

8

142

Green Gear 

Housing

Part Template - Litania

1

143

BGA24-02

Part Template - Litania

2

144

R4ZZ

Part Template - Litania

2

145

MS 16624 - 

0.250S 3100

Part Template - Litania

1

146

R4-2RS

Part Template - Litania

2

147

Green Gear 

Axle

Part Template - Litania

1

148

Green Gear 

Axle

Part Template - Litania

1

149

ANSI B18.8.2 

- 3_32 x 

5_8(2)

Part Template - Litania

2

150

GEN-8203

Part Template - Litania

2

151

57155K322

1

152

91590A113

2

153

Spur Gear 

a_1c_2-

n24014

1

154

PLTE00408

Axle Supple Plate

1

155

PLTE00406

PV Gear Box Mount Plate

2

156

HAND00103

Part Template - Litania

1

157

PLTE00407

PV Gear Box Trap Plate

1

158

HDWE012640

E0

HEX HD CAP SCREW- 1/4-20 X2 GRADE5

2

159

PV 2015 Hex 

Rod Housing

PV 2015 Hex Rod Housing

1

160

HDWE06269

#10-24 x 1" Flange Head Screw

4

161

Front Flat

Part Template - Litania

1

162

SHFT00035

PV UP/DOWN CRANK AXLE ROD

1

163

Rubber Edge 

Trim

Part Template - Litania

1

164

HDWE06246

1/4"-20 X 1/2" BUTTON-HEAD SOCKET CAP SCREW; SS

6

165

COVR00089

PV UPPER CHANNEL COVER

1

166

COVR00090

Part Template - Litania

1

167

HAND00121

Ball Knob; 11/16" OD; #10-32 Threads

2

168

HDWE09077

#10-32 Shoulder Bolt; 7/32" Long Shoulder; SS

6

169

Belt Trap Plate Part Template - Litania

2

170

CLMP00096

Back Timing Belt Clamp

1

171

CLMP00097

Front Tape Measure Clamp

1

172

HDWE061610

E0

#10-24 x 5/8" Phillips Head Screw

3

173

COVR00078

Adjustment Window; Depth

1

174

HDWE05029

#10 Flat Washer; 18-8 SS

3

175

HDWE05033

#10 Fender Washer

2

176

HDWE06284

#10-32 x 3/4" Button Head Screw

1

177

HDWE06263

1/4"-20 x 1.625" Button Head Socket Cap Screw; SS

1

178

HDWE58181

#10-32 x 1 1/4" Threaded Rod; Brass

1

179

HDWE05030

#8 FENDER WASHER; SS

8

180

SPCR00003

NYLON UNTHREADED SPACERS 5/16" OD; 3/8" LG

8

www.gillathletics.com

Copyright 

2016 by Gill Athletics.  

All rights reserved.

800-637-3090

10/8/2018

INST740110CXXYYSP

Page 14 of 17

740110CXXYYSP - AGX M4 POLE VAULT STANDARDS

INSTRUCTIONS

Summary of Contents for AGX M4 POLE VAULT


















Reviews:

No comments

Brands by name

Popular brands

Load more brands