manualshive.com logo in svg

Gigabyte G492-Z52, User Manual, Page: 83 / 137

Share
Download
Gigabyte G492-Z52 User Manual Download Page 83

- 83 -

BIOS Setup

Parameter

Description

Action on BIST Failure

Action to take when a CCD BIST failure is detected.
Options available: Do nothing, Down-CCD, Auto. Default setting is 

Auto

.

Fast short REP MOVSB

Default is 1, cab be set to zero for analysis purpose as long as OS supports 
it.
Options available: Disabled, Enabled. Default setting is 

Enabled

.

Enhanced REP MOVSB/
STOSB

Default is 1, cab be set to zero for analysis purpose as long as OS supports 
it.
Options available: Disabled, Enabled. Default setting is 

Enabled

.

REP-MOV/STOS Streaming

Allows REP-MOVS/STOS to use non-caching streaming stores for large 
sizes. 
Options available: Disabled, Enabled. Default setting is 

Enabled

.

X3D

Override of X3D technology.
Options available: Auto, Disable, 1 stack, 2 stacks, 4 stacks. Default setting 
is 

Auto

.

IBS hardware workaround

Sets if using IBS execution sampling without software workaround for 
erratum 1,285. May impact performance.
Options available: Auto, Enabled. Default setting is 

Auto

.

Summary of Contents for G492-Z52










































































































































Reviews:

No comments