Gigabyte G492-Z52 User Manual Download Page 8

Page: 8 / 137

- 8 -

Chapter 4 Motherboard Components ...........................................................................44

4-1  Motherboard Components ............................................................................. 44
4-2  Jumper Setting  .............................................................................................. 46
4-3  Backplane Board Storage Connector  ............................................................ 47

4-3-1 CBP20C5 ................................................................................................................47

Chapter 5 BIOS Setup ..................................................................................................48

5-1 The Main Menu .............................................................................................. 50
5-2 Advanced Menu ............................................................................................. 53

5-2-1  Trusted Computing .................................................................................................54
5-2-2  PSP Firmware Versions ..........................................................................................55
5-2-3  Legacy Video Select ...............................................................................................56

5-2-4 AST2600 Super IO Configuration

...........................................................................57

5-2-5 Serial Port Console Redirection .............................................................................59

5-2-6 CPU Configuration

..................................................................................................63

5-2-7 PCI Subsystem Settings .........................................................................................64

5-2-8 USB Configuration

..................................................................................................66

5-2-9 Network Stack Configuration

..................................................................................68

5-2-10 NVMe Configuration

...............................................................................................69

5-2-11 SATA Configuration

.................................................................................................70

5-2-12 Graphic Output Configuration

.................................................................................71

5-2-13 AMD Mem Configuration Status

.............................................................................72

5-2-14 Tls Auth Configuration

............................................................................................73

5-2-15 iSCSI Configuration

................................................................................................74

5-2-16 Intel(R) i350 Ethernet Controller .............................................................................75

5-2-17 VLAN Configuration

................................................................................................77

5-2-18 MAC IPv4 Network Configuration

...........................................................................78

5-2-19 MAC IPv6 Network Configuration

...........................................................................79

5-3 AMD CBS Menu ............................................................................................. 80

5-4 AMD PBS Menu ........................................................................................... 119

5-4-1 RAS ......................................................................................................................120

5-5 Chipset Setup Menu ..................................................................................... 122

5-5-1 North Bridge .........................................................................................................123

Summary of Contents for G492-Z52










































































































































Search results

Summary of Contents for G492-Z52

Reviews:

Gigabyte G492-Z52, User Manual, Page: 8 / 137

Search results

Summary of Contents for G492-Z52

Reviews: