Gigabyte G293-S40 User Manual Download Page 39 | Manualshive

Page: 39 / 118

background image

- 39 -

System Hardware Installation

3-6 Installing a PCI Express Card

• Voltages can be present within the server whenever an AC power source is connected. This

voltage is present even when the main power switch is in the off position. Ensure that the system
is powered-down and all power sources have been disconnected from the server prior to installing
a PCI card.

Failure to observe these warnings could result in personal injury or damage to equipment.

Follow these instructions to install a PCI Express x8 card on right side of the

system:

1. Loosen and remove the two screws securing the PCI Express card bracket on the right side of the

system.

2.  Remove the PCI Express card bracket from the system.
3.  Install the PCI Express card into the bracket.
4.  Secure the PCI Express card to the bracket with one screw.
5.  Install the PCI Express card bracket with card back into the system, ensure that the connector on

the bracket is securely installed into the connector on the motherboard as shown.

6. Secure the PCI Express card bracket with card to the system with two (2) screws.

2

1

1

«
...
37
38
39
40
41
...
»

Summary of Contents for G293-S40























































































































Reviews:

No comments

Related manuals for G293-S40

Brand: Xerox Pages: 40

Brand: F5 Pages: 72

Netfinity 6000R

Brand: IBM Pages: 218

eserver xSeries 440

Brand: IBM Pages: 74

eserver xSeries 440

Brand: IBM Pages: 98

eserver xSeries 440

Brand: IBM Pages: 84

Eserver xSeries 360 Type 8686

Brand: IBM Pages: 184

eserver xSeries 350

Brand: IBM Pages: 62

eServer xSeries 135

Brand: IBM Pages: 62

eserver pSeries 690

Brand: IBM Pages: 212

System x3690 X5

Brand: IBM Pages: 32

System x3690 X5

Brand: IBM Pages: 33

System x3690 X5

Brand: IBM Pages: 180

Brand: IBM Pages: 1032

Brand: IBM Pages: 56

System x3350 Type 4192

Brand: IBM Pages: 84

BladeCenter JS20

Brand: IBM Pages: 132

NOP1840 PEP-Box

Brand: Newtec Pages: 96

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands