Gigabyte G293-S40 User Manual Download Page 87

Page: 87 / 118

- 87 -

BIOS Setup

5-3-4

Memory Configuration

Parameter

Description

Integrated Memory Controller (iMC)

Enforce POR

When set to Enable, the system enforces Plan Of Record restrictions
for DDR4 frequency and voltage programming.
Options available: POR, Disable. Default setting is

Disable

Memory Frequency

Configures the maximum memory frequency. If Enforce POR is

disabled, user will be able to run at higher frequencies than the
memory support (limited by processor support).
Default setting is

Auto

Enable ADR

Enables the detecting and enabling of ADR (Asynchronous DRAM
Refresh) function.
Options available: Enable, Disable. Default setting is

Enable

Legacy ADR Mode

Enable/Disable the Legacy ADR Mode.
Options available: Enable, Disable. Default setting is

Disable

Minimum System Memory Size

Configures the minimum memory size.

Options available: 2GB, 4GB, 6GB, 8GB. Default setting is

2GB

ADR Data Save Mode

Specifies the Data Save Mode for ADR. Batterybacked or Type 01

NVDIMM.

Options available: Disable, Batterybacked DIMMs, NVDIMMs.
Default setting is

NVDIMMs

Erase-Arm NVDIMMs

Enable/Disable Erasing and Arming NVDIMMs.
Options available: Enable, Disable. Default setting is

Enable

Summary of Contents for G293-S40























































































































Search results

Summary of Contents for G293-S40

Reviews:

Related manuals for G293-S40

Brands by name

Popular brands

Gigabyte G293-S40, User Manual

Search results

Summary of Contents for G293-S40

Reviews:

Related manuals for G293-S40

Brands by name

Popular brands