Gigabyte G293-S40 User Manual Download Page 33

Page: 33 / 118

- 33 -

System Hardware Installation

For Slot3/Slot4/Slot5/Slot6

Follow these instructions to install the GPU card:

1. [For Slot5/Slot6] Loosen and remove the two screws securing the PCI cage at the top of the

system.

[For Slot3/Slot4] Loosen and remove the single screw at the top of the system and the two screws

at the rear of the system securing the PCI cage.

Pull the two plastic handles to lift up the PCI cage from the system.

2. Insert the card into the selected slot. Make sure that the card is properly seated.
3. Secure the GPU cards in place with two screws.

Front

Rear

Boom: Slot4 (PCIE_2_PCIE_1)

Top: Slot3 (PCIE_2_PCIE_2)

Boom: Slot6 (PCIE_3_PCIE_1)

Top: Slot5 (PCIE_3_PCIE_2)

(For Slot5/Slot6)

Summary of Contents for G293-S40























































































































Search results

Summary of Contents for G293-S40

Reviews:

Related manuals for G293-S40

Brands by name

Popular brands

Gigabyte G293-S40, User Manual

Search results

Summary of Contents for G293-S40

Reviews:

Related manuals for G293-S40

Brands by name

Popular brands