Gigabyte 6NE152ZE0MR-00 User Manual Download

Page: 107 / 138

- 107 -

BIOS Setup

Parameter

Description

DF Cstates

Enable/Disable DF C-states.
Options available: Auto, Enabled, Disabled. Default setting is

Auto

CPPC

Enable/Disable the CPPC feature.
Options available: Auto, Enabled, Disabled. Default setting is

Auto

HSMP Support

Select HSMP support enable or disable.
Options available: Auto, Enabled, Disabled. Default setting is

Auto

DLMM Support

Select DLMM support enable or disable.
Options available: Auto, Enabled, Disabled. Default setting is

Auto

BoostFmaxEn

Options available: Auto/Enabled. Default setting is

Auto

EDC Current

Options available: Enable, Disable. Default setting is

Disable

LCLK Frequency Control

Press [Enter] for advanced configuration.

DF PSTATE Mode Select

Option available: Normal, limit Highest, Limit All, Auto.
Default setting is

Auto

Summary of Contents for 6NE152ZE0MR-00











































































































































Search results

Summary of Contents for 6NE152ZE0MR-00

Reviews:

Related manuals for 6NE152ZE0MR-00

Brands by name

Popular brands

Gigabyte 6NE152ZE0MR-00, User Manual

Search results

Summary of Contents for 6NE152ZE0MR-00

Reviews:

Related manuals for 6NE152ZE0MR-00

Brands by name

Popular brands