Gigabyte 6NE152ZE0MR-00 User Manual Download

Page: 117 / 138

- 117 -

BIOS Setup

5-4 AMD PBS Menu

AMD PBS Option menu displays submenu options for configuring the function of AMD PBS. Select a
submenu item, then press [Enter] to access the related submenu screen.

Parameter

Description

RAS

Press [Enter] for configuration of advanced items.

SPI Locking

Enable/Disable SPI Locking for protect ROM part.
Options available: Enabled/Disabled. Default setting is

Disabled

iLA TraceMemoryEn

Reserved 1M bytes MMIO space on 1M boundary when iLA TraceMemoryEn
disabled.
Options available: Enabled/Disabled. Default setting is

Disabled

iLA TraceMemoryEn
reserved MMIO

Reserved function.

SRIS mode debug

Control SRIS mode debug.
Options available: Auto/Enabled/Disabled. Default setting is

Auto

SRIS Autodetect

Control SRIS Autodetect.
Options available: Auto/Enabled/Disabled. Default setting is

Auto

Summary of Contents for 6NE152ZE0MR-00











































































































































Search results

Summary of Contents for 6NE152ZE0MR-00

Reviews:

Related manuals for 6NE152ZE0MR-00

Brands by name

Popular brands

Gigabyte 6NE152ZE0MR-00, User Manual

Search results

Summary of Contents for 6NE152ZE0MR-00

Reviews:

Related manuals for 6NE152ZE0MR-00

Brands by name

Popular brands