Gigabyte 6NE152ZE0MR-00 User Manual Download Page 128

Page: 128 / 138

BIOS Setup

- 128 -

5-6-4

IPv6 BMC Network Configuration

Parameter

Description

IPv6 BMC network configuration

IPv6 BMC Lan Channel 1

IPv6 BMC Lan Option

Enable/Disable IPv6 BMC LAN channel function. When this item is
disabled, the system will not modify any BMC network during BIOS
phase.

Options available: Unspecified, Disable, Enable. Default setting is

Enable

IPv6 BMC Lan IP Address
Source

Selects to configure LAN channel parameters statically or dynamically (by

BIOS or BMC).

Options available: Unspecified, Static, Dynamic-Obtained by BMC

running DHCP. Default setting is

Enable Dynamic-Obtained by BMC

running DHCP

IPv6 BMC Lan IP Address/

Prefix Length

Check if the IPv6 BMC LAN IP address matches those displayed on the
screen.

Summary of Contents for 6NE152ZE0MR-00











































































































































Search results

Summary of Contents for 6NE152ZE0MR-00

Reviews:

Related manuals for 6NE152ZE0MR-00

Brands by name

Popular brands

Gigabyte 6NE152ZE0MR-00, User Manual

Search results

Summary of Contents for 6NE152ZE0MR-00

Reviews:

Related manuals for 6NE152ZE0MR-00

Brands by name

Popular brands