manualshive.com logo in svg

Giant Leap Rocketry TALON 6, Instructions Manual, Page: 7 / 36

Share
Download
Giant Leap Rocketry TALON 6 Instructions Manual Download Page 7

(with finger tight u-bolts) down the motor tube 

U-BOLT LOOP ENDS POINTING 

AWAY

 FROM THE SLIMLINE UNTIL THE CENTERING RINGS ARE 21’’ TO 

THE CLOSEST PART OF THE PREVIOUSLY MOUNTED SLIMLINE RETAINER.   
  
Take a marking pen and make a circular mark on the motor tube on both sides of the 
centering ring assembly.  Next, temporarily move the assembly approximately six inches 
back up the tube away from the Slimline.  Loosen the u-bolts (but do not remove) and 
spread a thin layer of epoxy between the two centering rings and bring together by 
securely tightening both u-bolts. BEFORE THAT EPOXY HAS TIME TO CURE, 
epoxy this centering ring assembly into place on the motor tube (between the previously 
made marks) securely using a generous amount of epoxy.  
  
BE CERTAIN THIS ASSEMBLY IS “SQUARE” TO THE MOTOR TUBE AND USE 
TAPE TO HOLD IN POSTION.   
  

THIS IS A CRITICAL JOINT

 AND MUST BE STRONG.  BE CERTAIN THIS 

ASSEMBLY IS 21” TO THE VERY CLOSEST PART OF THE PREVIOUSLY 
MOUNTED SLIMLINE. Be sure you place epoxy on all mating surfaces and have fillets 
on both sides of the centering rings.  

ALLOW THIS JOINT TO CURE WITH NO 

EPOXY RUNS!

  Also place a small drop of epoxy on the exposed u-bolt threads.  Be 

certain there is no excess epoxy on the motor tube where it shouldn’t be. 
 
Locate the 6” x 3.0” centering ring with two extra 1⁄2” holes in each,  and slide onto the 
forward end of the motor tube (away from the Slimline end) PLACING THE CLOSEST 
PART OF THE CENTERING RING EXACTLY 4.25” FROM THE FRONT OF THE 
MOTOR TUBE. Place a circular mark around the motor tube, on both sides of the 
centering ring. 

BEFORE YOU USE ANY EPOXY, 

make sure that the small 1⁄2” holes 

will be in a 

STRAIGHT-LINE BACK

 to the u-bolts mounted in the previous step,

 

   

 

 

  

Summary of Contents for TALON 6





































Reviews:

No comments