manualshive.com logo in svg

Giant Leap Rocketry TALON 6, Instructions Manual, Page: 27 / 36

Share
Download
Giant Leap Rocketry TALON 6 Instructions Manual Download Page 27

 
When the above assembly is finished, be sure all Kevlar cord is pulled tight inside of the 
airframe and all excess is outside. 

   

  

  

 

 

 

Apply a fillet of epoxy around the top of the centering ring inside the coupler.  Now 
grasp the coupler centering ring assembly in one hand and the Kevlar cord in the other 
pulling the centering ring assembly CLOSE TO THE COUPLER BUT LEAVING 
SEVERAL INCHES OF SPACE BETWEEN THE TWO PARTS AND NO KEVLAR 
CORD IS “SLACK” BETWEEN THE PARTS.  Apply another ring of epoxy 
approximately one inch wide around the top edge of the coupler and a light coat on the 
outside edges of the centering ring assembly.  Permanently press into position the 
centering ring assembly inside of the coupler with approximately1/8” of coupler 
extending above the bulkhead assembly.

  WARNING, BE CERTAIN ALL EXCESS 

KEVLAR CORD IS PULLED OUT OF THE AIRFRAME/COUPLER AND THE 
HOLES IN THE CENTERING RING ASSEMBLY ALLOWING THE KEVLAR 
CORD TO PASS THROUGH ARE IN A STRAIGHT LINE WITH THE 
REMAINING TAUNT KEVLAR CORD IN THE SLOTTED AIRFRAME.  BE 
CERTAIN THE KEVLAR CORD IS NOT UNDERNEATH ANY OF THE FIN 
SLOTS.  TRY TO KEEP EPOXY OFF OF THE KEVLAR CORD.  

Stand entire 

assembly up-right and allow epoxy to cure.

 

 

Summary of Contents for TALON 6





































Reviews:

No comments