manualshive.com logo in svg

Giant Leap Rocketry TALON 6, Instructions Manual, Page: 28 / 36

Share
Download
Giant Leap Rocketry TALON 6 Instructions Manual Download Page 28

  

 

 

 

Locate the two 5/16” quick-links and 1⁄2” x 25’ Kevlar shock loop.  Insert a quick link 
through each loop end and attach one loop to the above 1⁄2” Kevlar between u-bolts that 
extends above the airframe coupler.  The opposite end of the shock loop will eventually 
attach via 5/16” quick-link and the Kevlar bridle to the lower part of the av-bay located 
inside of the upper airframe. 
  

IF YOUR TALON SIX HAS A PHENOLIC AIRFRAME, NOW IS AN 
EXCELLENT TIME TO COVER THE TUBING WITH EITHER FIBERGLASS, 
CARBON FIBER OR THE ENCLOSED EZ-GLASS SOCK 
REEINFORCEMENT.

  It is unnecessary to cover a fiberglass airframe with tube 

reinforcement.  BUT IT IS IMPORTANT, WHICHEVER TALON 6 YOU 
PURCHASED, THAT YOU APPLY A 2” WIDE STRIP OF FIBERGLASS TAPE 
AND RESIN COMPLETELY AROUND THE TAILCONE-BODY TUBE JOINT. 
 Failure to do so will result in a crack in the final paint finish around the entire 
circumference when the rocket lands under parachute.  Cut out the airframe slots after 
application of the reinforcement. 

FIN INSTALLATION 
  

  

 

 

Summary of Contents for TALON 6





































Reviews:

No comments