Ghost Acoustic/MIDI system User Manual Download Page 13 | Manualshive

Page: 13 / 32

background image

Saddle Pickups & Pagoda Shim

For guitars with ﬂat ﬁngerboards, such as clas-
sical guitars, the Pagoda Shim is not used. The
saddle pickups sit on the bottom of the saddle slot.

��

��

��

��

��

��

��

��

��

��

��

The saddles pickups ﬁt in a 1/8” (3.2mm) saddle slot.
They are slightly oversized to permit sanding to a
snug ﬁt. Each saddle is marked with a dot to orient the
pickup properly. This dot must face towards the fret-
board so that the pickup senses the string optimally.

11

«
...
11
12
13
14
15
...
»

Summary of Contents for Acoustic/MIDI system

































Reviews:

No comments

Related manuals for Acoustic/MIDI system

Brand: GE Pages: 36

Brand: TCL Pages: 16

RAY-DANZ TS9030

Brand: TCL Pages: 32

Brand: TCL Pages: 19

Brand: Yamaha Pages: 7

Brand: R-Tech Pages: 57

Brand: akira Pages: 15

Brand: Vonyx Pages: 16

Brand: BST Pro Pages: 9

Brand: Barnstead|Thermolyne Pages: 56

Brand: JBL Pages: 8

Smarty 4X P 1.1

Brand: Salda Pages: 30

Brand: Patrol Hawk Pages: 13

Brand: Aiphone Pages: 2

Kaysun Aquantia R-32 PRO

Brand: Frigicoll Pages: 44

Brand: ESAB Pages: 44

Brand: Thermal Arc Pages: 56

Brand: Bose Pages: 30

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands