Ghost Acoustic/MIDI system User Manual Download Page 25 | Manualshive

Page: 25 / 32

background image

23

Control Knobs

A  set  of  three,  stacked  rosewood  and  brass  knobs
is  available  from  Graph  Tech  as  a  separate  item,
with  a  1/16”  hex  key  included  for  installation.
Or  you  can  provide  your  own  knobs.  Secure  the
knobs  onto  the  pot  shafts  by  means  of  the  set
screws.  Leave  a  little  clearance  between  the  inner
and  outer  knobs  so  that  they  turn  independently.

Pot Shaft Diameters:

outer, 0.236” (6.0mm); inner, 0.139” (3.5mm)

«
...
23
24
25
26
27
...
»

Summary of Contents for Acoustic/MIDI system

































Reviews:

No comments

Related manuals for Acoustic/MIDI system

Brand: Panasonic Pages: 124

Brand: Magnadyne Pages: 20

Brand: salmson Pages: 12

Brand: Jensen Pages: 12

Brand: Parkside Pages: 201

Brand: Parrot Products Pages: 8

Brand: YA Pages: 14

Metalmaster 200d Pro DC GTAW

Brand: Tokentools Pages: 33

Brand: Clarke Pages: 24

Brand: Mirage Pages: 1

Brand: Sierra Pages: 11

Brand: Videx Pages: 60

Brand: EAW Pages: 2

Brand: Onn Pages: 11

Brand: Pure Acoustics Pages: 1

Brand: Valcom Pages: 2

Brand: Magnavox Pages: 33

Brand: Electro-Voice Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands