Ghost Controls Ghost Pro LSM1 Installation And Owner'S Manual Download Page 39

Page: 39 / 68

P U S H - T O - O P E N

2 0 2 0

PUSH-TO-OPEN: GATE SWINGS TO OPEN OUTSIDE PROPERTY

The dimensions and step-by-step instructions that follow are for mounting the GHOST CONTROLS

Gate Operator

PUSH-TO-OPEN installation system to a standard gate that swings away from your property.

You will need to make sure

you purchase the Push-To-Open Bracket Kit (AXPO) before you start installing.
FOR PULL-TO-OPEN APPLICATIONS, PLEASE SEE PULL-TO-OPEN APPLICATION ON “PULL TO OPEN

INSTALLATION” ON PAGE 19.

STEP 1.

Establish and mark the horizontal center lines of the gate and the post for proper alignment

of gate brackets.

NOTE

This center point will be used

for mounting the post bracket

in STEP 4.

PUSH TO OPEN INSTALLATION

OPERATOR ARM INSTALLATION

NOTE

Wheels cannot be used with

any Ghost Controls

gate

opener system!

For gates weighing over 200

lbs. ball bearing hinges are

recommended.

Operator is not for use on

solid panel privacy gates.

Summary of Contents for Ghost Pro LSM1





































































Search results

Summary of Contents for Ghost Pro LSM1

Reviews:

Related manuals for Ghost Pro LSM1

Brands by name

Popular brands

Ghost Controls Ghost Pro LSM1, Installation And Owner'S Manual

Search results

Summary of Contents for Ghost Pro LSM1

Reviews:

Related manuals for Ghost Pro LSM1

Brands by name

Popular brands