Ghost Controls Ghost Pro LSM1 Installation And Owner'S Manual Download Page 44 | Manualshive

Page: 44 / 68

background image

44

P U S H - T O - O P E N

© G h o s t C o n t r o l s

®

2 0 2 0

INSTALLING THE CONTROL BOX AND *BATTERY BOX KIT

(*Battery Box Kit (ABBT2), Not Included)

STEP 7.

Determine the mounting location for the control and *optional battery box. The battery and

control box must be located within 4 feet of each other. Then install.

NOTE

Mount the control box a minimum of 3 feet above the ground to keep dirt and water from damaging the control board

and within 4 feet of the operator arm in order for the operator cable to reach the control box.

A. Pre-drill (4) holes (7/32˝ drill bit) in backside of control and optional battery box, and through the fencing

where you will be securing the control box and battery box.

B. Now use the (4) supplied phillips screws for each box to mount the control box and optional battery box to

the fence.

C. Make sure the on/off switch on the bottom of control box is in the off position.

«
...
42
43
44
45
46
...
»

Summary of Contents for Ghost Pro LSM1





































































Reviews:

No comments

Related manuals for Ghost Pro LSM1

Brand: Wayne-Dalton Pages: 24

Brand: tau Pages: 44

Brand: 4Ddoors Pages: 26

Brand: Gamatech Pages: 26

Brand: Viking Pages: 49

Brand: tau Pages: 40

Brand: US Automatic Pages: 23

Brand: USAutomatic Pages: 76

Brand: Dea Pages: 14

Brand: Chamberlain Pages: 88

Brand: DACE Pages: 52

Brand: quiko Pages: 42

Walk-n-Cut 76503

Brand: Hamilton Beach Pages: 10

Brand: quiko Pages: 16

Brand: Erreka Pages: 106

Brand: Hamilton Beach Pages: 10

Brand: Manaras Pages: 52

Brand: Ricoh Pages: 171

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands