manualshive.com logo in svg

GHM GREISINGER GIA 20 EB, Mounting And Operating Manual

Share
Download
GHM GREISINGER GIA 20 EB Mounting And Operating Manual Download Page 18

E31.0.12.6C-06 

Mounting and operating manual GIA 20 EB with electrically insulated supply

 

page 18 of 32 

6.4. Measuring of frequency  (TTL, switching-contact) 

This chapter describes how to configure the device for measuring frequency.  
This instruction demands that you selected “

FrEq

“ as your desired input type like it is explained in 

chapter 6.1.  

The display must show 

INP

.  

Parameter 

Button 1 

Value 

Button 2 / 3 

Notes 

SENS

 

 

TTL

 

TTL-signal (see info connection)

 

NPN

 

Switching contact, NPN 
For direct connection of a passive switching contact (e.g. push 
button, relay) or transmitter with NPN output. 
There is a internal pull-up-resistor.  
(see info switching contact) 

PNP

 

Switching contact, PNP 
For direct connection of a transmitter with PNP output.                                                     
There is a internal pull-down-resistor. 

FR.LO

 

0 ... 9999 

lower frequency range 

FR.K,

 

FR.LO ... 9999 

upper frequency range 

DP

 

"- - - -" 

 "- - - . -"   
 "- - . - -" 

"- . - - -" 

Decimal point 

D,.LO

 

-1999 ... 9999 

display at lower frequency range limit 

D,.K,

 

-1999 ... 9999 

display at upper frequency range limit 

L ,

 

(Limit) 

OFF

 

Exceeding of the measuring-frequency is tolerable until you 
reach the maximum measuring range limit.

 

ON.ER

 

The measuring range is exactly bounded by the selected fre-
quency-measuring-range-limit. When exceeding or short falling 
of the limit the device will display an error message.

 

ON.RG

 

The measuring range is exactly bounded by the selected meas-
uring-range-limit. When exceeding or short falling of the limit the 
device will display the lower or upper display-range-limit.

  

e.g. humidity:  
when exceeding, the device will display 0% or 100% 

F,LT

 

0.01 ... 2.00

 s 

Filter

 

O

 V

TP 

 

Output configuration will be explained in chapter 7. According to 
your settings different parameters will be shown. 

 

Finish configuration: 

Press

 Button 1

 as often till the device executes a reset. The values will be stored at it.

 

.

 

Switching contact, NPN:

 

when using push-buttons or relays, they must be bounce-free!

 

Connection:

 

For the connection of a frequency-transmitter, please follow the instructions given in chapter 5.3.6. 
When connecting a switching-contact-transmitter with increased frequency range (= with external 
circuitry) you have to select TTL as input signal. 

Summary of Contents for GREISINGER GIA 20 EB

































Reviews:

No comments

Brands by name

Popular brands

Load more brands