background image

                                                  

Gfp 865DH

 

February 2018

 

 

 

1.

 

Introduction 

Thank  you  for  choosing  a  Gfp  laminator.    It  has  been  designed  and  manufactured  to  provide 
years of continuous service.  Please read this manual thoroughly before operating.  Please inspect 
the box and the laminator for shipping damage.   Damage should be brought to the attention of 
the  delivering  carrier  immediately.      For  a  list  of  shipping  components  see  “Packing  List”  on 
page 9.   

2. Important Safety Instructions   

 

In this operating manual you will find important safety messages regarding the product. 
Read  these  instructions  carefully,  failure  to  comply  with  the  following  safety  procedures  could 
result in serious injury. 

WARNING

 Do not attempt to service or repair the laminator.  Only authorized      maintenance 

and service technicians should make repairs. 

WARNING

  Do  not  connect  the  laminator  to  an  electrical  supply  or  attempt  to  operate  the 

laminator  until  you  have  completely  read  these  instructions.    Maintain  these 
instructions in a convenient location for future reference.

 

 

WARNING

  To  guard  against  injury,  the  following  safety  precautions  must  be  observed  in  the 

installation and use of the laminator 

3.

 

Installation Safeguards  

 

 

Shipping damage should be brought to the immediate attention of the delivering carrier 

 

Avoid locating the laminator near sources of heat or cold.  Avoid locating the laminator in 
the direct path of forced, heated or cooled air 

 

The receptacle must be located near the equipment and easily accessible. 

 

 

Connect the attachment plug provided with the laminator to a suitably grounded 

outlet  only.    This  machine  must  have  reliable  earth  wire  to  ensure  the  safety  of  the 
machine during operations 

 

Contact an electrician should the attachment plug provided with the laminator not match 
the receptacles at your location 

 

 

Ensure  that  the  voltages  of  the  power  supply  you  are  using  match  the  rated 

working voltages before operations. Do not use incorrect power supply

 

 

 

Do not use damaged wires or sockets.  If abnormal conditions occur, switch off 

the power supply first. 

 

 

Only a licensed electrician should install wiring and outlet for the laminator 

 

Do not defeat or remove electrical and mechanical safety  equipment such as interlocks, 
shields and guards 

Summary of Contents for 865DH





























Reviews: