Gewiss CHORUS GWA9531 Technical Manual Download Page 48 | Manualshive

Page: 48 / 57

background image

48



Input- Manual Dimming (n.6)

This object is used to adjust the brightness.
The enabled flags are C (communication) and W (written by bus).
The standard format of the object is 3.007 DPT_Control_Dimming.
The standard format of the object is

4 bit and the information it contains is

“increase %

/decrease

%”.



Input- Follow-up time in minute (n.7)

This object is used to set the follow-up time.
The enabled flags are C (communication) and W (written by bus).
The standard format of the object is 7.006 DPT_TimePeriodMin.
The standard format of the object is

2 byte and the information it contains is

“

VALUE

(min)

”.



Input- Overwrite threshold 1 (n.8)

This object is used to overwrite threshold 1.
The enabled flags are C (communication) and W (written by bus).
The standard format of the object is 9.004 DPT_Value_Lux.
The standard format of the object is

2 byte and the information it contains is

“VALUE

(lux)”.



Toggle threshold 1 and 2 (n.9)

This object is used to switch between threshold 1 and 2. .
The enabled flags are C (communication) and W (written by bus).
The standard format of the object is 1.003 DPT_Value.
The standard format of the object is

1 bit and the information it contains is

“enable/disable”.



Input- Switch set value and fixed value (n.10)

This object is used to set a value fixed brigthness.
The enabled flags are C (communication) and W (written by bus).
The standard format of the object is 1.003 DPT_Value.
The standard format of the object is

1 bit and the information it contains is

“enable/disable”.



Input- Start/Stop burn-in function (n.11)

This object is used to start or stop the Burn-in function.
The enabled flags are C (communication) and W (written by bus).
The standard format of the object is 1.010 DPT_Start.
The standard format of the object is

1 bit and the information it contains is

“Start/Stop”.



Input- Retrieve burn-in time (n.12)

This object is used to trigger the spontaneous sending of the remaining burn-in time
that is sent through the object

“Output- burn-in time status” (n.19)

The enabled flags are C (communication) and W (written by bus).
The standard format of the object is 1.010 DPT_Start.
The standard format of the object is 1 bit and the information it contains is

“Start/Stop”.

«
...
46
47
48
49
50
...
»

Summary of Contents for CHORUS GWA9531


























































Reviews:

No comments

Related manuals for CHORUS GWA9531

Brand: GÄN Pages: 24

Brand: Falcon Pages: 8

Brand: Talkswitch Pages: 334

Brand: Tait Pages: 41

Brand: Tait Pages: 149

Brand: Tait Pages: 132

Brand: Zebronics Pages: 6

Brand: HBX Pages: 12

Brand: AIA Pages: 8

Brand: Eco Pages: 34

Care@Home MDsense

Brand: Essence Smartcare Pages: 12

5TH GEN 4RUNNER

Brand: Victory 4x4 Pages: 5

Brand: Keith Pages: 2

WrapAround Windjammer

Brand: Bestop Pages: 7

Ceiling Trim Kit for Home2 Series

Brand: Elite Screens Pages: 8

Brand: Bison Pages: 3

Brand: Thule Pages: 8

Brand: LANSING LIGHTING Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands