background image

 

 

Page: 3 of 16

 

Copyright © 2013 GenTent Safety Canopies, LLC – All Rights Reserved 

V5 – July, 2013 

IMPORTANT PRODUCT SAFETY 

 

Please review these important safety warnings, cautions and notes in order to assure safe and 

effective use of your generator in wet weather.  

 

WARNING 

 

Always shut generator off before any fueling or maintenance procedures.  

 

WARNING  

Never 

position the refueling door on the same side of the generator as the exhaust muffler. 

Spilled gasoline can result in fire.  

 

WARNING 

 

Never 

block or cover the generator exhaust muffler in any way. GenTent canopy must be 

installed above generator exhaust muffler. Install GenTent electrical skirts such that they 

cannot 

block exhaust in any way.  Keep the GenTent canopy at least 6 inches away from direct contact 

with the exhaust.  

 

WARNING 

Always install included washer between the knob and the clamp base.  Tightening the 

knob without using the washer VOIDS the WARRANTY as it risks breakage.  

 

CAUTION  

Over tightening clamps should be avoided. 

If you notice the mouth of the clamp pulling aware 

from the frame, the clamping strength has been reduced and the knob should be loosened.  

 

CAUTION  

Always grasp fiberglass rods firmly during installation to avoid the whipping motion that can 

occur when a bent fiberglass rod is mistakenly released.  

 

CAUTION  

Avoid using your portable generator in hurricane force winds above 70mph. 

 

NOTE  

Should generator handles cause significant stretching of the elastic straps when extended, it is advisable 

to release the elastics straps on the handle side of the generator before extending generator handles.  

 

NOTE 

 

Should GenTent cover block pull starter, it is advisable to release the elastic straps on the pull starter side 

and temporarily move GenTent canopy out of the way.  

 

NOTE  

When using GenTent during snow storms, it is recommended to periodically brush away any accumulation 

that blocks the top vent.

  

Summary of Contents for StormBracer

















Reviews: