background image

1

 

 

NOTICES 

 

This device complies with Part 15 of the FCC rules.  Operation is subject to the 

following two conditions . 

1. This device may not cause harmful interference. 

2. This device mus t accept any interference received,  including interference that 

may cause undesired operation. 

 

NOTE: This equipment has been tested and found to comply with the limits for a 

Class B digital device, pursuant to Part 15 of the FCC  rules. These limits are 

designed to provide reasonable protection  against harmful interference in a 

residential installation. This  equipment generates, uses and can radiate radio 

frequency energy and, if not installed and used in accordance with the instruction 

manual, may cause ha rmful interference to radio communications.   

However, there is no guarantee that interference will not occur in a  particular 

installation. If this equipment does cause harmful  interference to radio or 

television reception, which can be determined by turning the equipment off and on, 

the user is encouraged to try to  correct the interference by one or more of the 

following measures: 

• Reorient or relocate the receiving antenna 

• Increase the separation between the equipment and the receiver 

• Connect the equipment into an outlet on a circuit different from 

that to which the receiver is connected 

• Consult the dealer or an experienced ratio/TV technician for help 

 

WARNING!  

Any changes or modifications of equipment not expressly approved by Intersil   

could void the user’s authority to operate the equipment.  

 

 

 

 

 

 

 

Summary of Contents for GWL-2400P
















Reviews: