background image

10 

and then Network Adapters. If you find the Yellow (?) sign on the adapter, 

it shows the installation is not successful. Select the adapter and click on 

Remove. Restart your computer after uninstalling the driver to make the 

changes effective.   

11) Right click on the Network Neighborhood using the mouse. 

12) Select Properties from  the pop up menu. The network box appears and you 

see three main tabs : Configuration, Identification and Access Control. 

13) Click on the Configuration tab and then click on the Add button. Select 

Network Component Type box appears. Click on the Protocol then click 

Add button.  

14) Select Network Protocols box appears. From the list of manufactures, click 

on Microsoft. From the list of network protocols list, select NetBEUI, then 

click OK. 

15) The NetBEUI protocol is now installed. After clicking on OK return back 

to Network Component Type box. 

16) Repeat the step 13 and 14 to add IPX/SPX protocol. 

17) Repeat the step 13 and 14 to add TCP/IP protocol. 

18) Click on the TCP/IP option for setting the IP address for your computer. 

You can select either Static or DHCP settings. If you use the static IP setup 

then enter the IP value, Subnet masking, DNS, Domain/Workgroup name, 

and Gateway Address values. After setting these parameters appropriately, 

click OK to return to Network Component Type and you can select the File 

and Printer Shari ng options as well as the Access to your computer by 

other users connected to that network by setting the computer sharing 

options. Click OK. 

19) Screen message do you want to restart your Computer will pop up. Select 

Yes. It will shut down your computer and will restart. 

 

 

3-2 Uninstallation Method 

 

If you want to unistall the PCMCIA card under Win 95 (OSR2)/98, click on the 

Start at the left bottom of your screen. Select the Programs. Click on the 

GENOTECH and click on Uninstall. Confirm message about removing the 

“ GENOTECH uninstall” and all of its components appear. Click on Yes. 

UnistallShield removes the software  “ GENOTECH uninstall” successfully. Click 

Summary of Contents for GWL-2400P
















Reviews: