background image

BLIZZARD  500-900 

13 

532102        -  Rev.B

1

2

13

1

15

16

13

3

1

2

18

14

2x17

1

2

0 1

2

3

4 5

6

Tr

ansla

tion of the original instruc

tions

ENGLISH

4.  Bring the base of the gear motor to 18mm from the base plate 

using the four support nuts (

14

-1).

5.  Fit four M10 locknuts and four washers, supplied with the base 

plate, as in 

14

-2.

6.  Ensure there is 13.5mm between the pinion and the sliding gate 

section (§ 5.2-

9

-

10

).

7.  Use a spirit level to check that the gear motor is horizontal (

14

): 

make any adjustments with the support nuts (

14

-1).

8.  Provisionally tighten the four locknuts using two hex spanners 

(

14

-1-2).

5.5  MANUAL OPERATION

!

Shut off the power to the system and ensure that the automation 
system is stopped before performing manual movement operations 
and restoring automatic operation.

A lock with personalised key is available as an optional accessory.

MANUAL RELEASE

1.  Open the plastic cap on the release device (

15

-1).

2.  Turn the lock clockwise using a coin or your personalised key 

(

15

-1).

3.  Turn the knob clockwise (

15

-2).

RESTORING AUTOMATIC OPERATION

1.  Turn the knob anticlockwise.
2.  Turn the lock anticlockwise.
3.  Manually move the gate until the mechanical system engages.

5.6  INSTALLING THE RACK

RISKS

PERSONAL PROTECTIVE EQUIPMENT

The rack installation accessories contain screws for aluminium or steel 
sliding gate sections. Use specific screws for other materials.
Do not use grease or other lubricants. 

Manually close the gate (§ 5.5).

STEEL RACK WITH SPACERS TO BE WELDED ON

Do not weld the rack components to the spacers or to each other.

1.  Install the spacers and screws in the upper part of the slots

(

16

-1): This will allow future adjustments if the rail is lowered.

2.  Rest the assembled component on the pinion.

Summary of Contents for BLIZZARD 500























Reviews: