Genie S-80 XC Operator'S Manual Download Page 52

Page: 52 / 73

Operator's Manual

First Edition • Second Printing

Operating Instructions

50 S

-80 XC

™

• S

-85 XC

™

Part No. 1279298GT

If the tilt alarm sounds with
the platform uphill:

Lower the boom.

Retract the boom.

If the tilt alarm sounds with
the platform downhill:

Retract the boom.

Lower the boom.

Platform Overload Indicator Light

Light flashing indicates the platform
is overloaded. The engine will stop
and no functions will operate.

Remove weight from the platform
until the light goes off and then
restart the engine.

Machine Malfunction Indicator Light

Light on indicates a system fault.

Push in and then pull out the red Emergency
Stop button.

Lower and retract the boom.

Tag the machine and remove from service.
Functions will not operate.

Summary of Contents for S-80 XC










































































Search results

Summary of Contents for S-80 XC

Reviews:

Related manuals for S-80 XC

Brands by name

Popular brands

Genie S-80 XC, Operator'S Manual

Search results

Summary of Contents for S-80 XC

Reviews:

Related manuals for S-80 XC

Brands by name

Popular brands