Genie S-80 XC Operator'S Manual Download Page 18

Page: 18 / 73

Operator's Manual

First Edition • Second Printing

Work Area Safety

16 S

-80 XC

™

• S

-85 XC

™

Part No. 1279298GT

Fall Hazards

Occupants must wear a
safety belt or harness in
accordance with
governmental regulations.
Attach the lanyard to the
anchor provided in the
platform.

Do not sit, stand, or climb
on the platform guard rails.
Maintain a firm footing on
the platform floor at all
times.

Do not climb down from the
platform when raised.

Keep the platform floor clear of debris.

Lower the platform entry mid-rail or close the entry
gate before operating.

Do not enter or exit the platform unless the
machine is in the stowed position and the platform
is at ground level.

Hazards related with the specific product
application of exiting at height have been
considered in the design of the machine, for further
information contact Genie (see section Contacting
the Manufacturer).

Collision Hazards

Be aware of limited sight
distance and blind spots
when driving or operating.

Be aware of the boom position and tailswing when
rotating the turntable.

Check the work area for
overhead obstructions or
other possible hazards.

Be aware of crushing
hazards when grasping the
platform guard rail.

Operators must comply with employer, job site, and
governmental rules regarding use of personal
protective equipment.

Summary of Contents for S-80 XC










































































Search results

Summary of Contents for S-80 XC

Reviews:

Related manuals for S-80 XC

Brands by name

Popular brands

Genie S-80 XC, Operator'S Manual

Search results

Summary of Contents for S-80 XC

Reviews:

Related manuals for S-80 XC

Brands by name

Popular brands