Genie S-100HD Operator'S Manual Download Page 39

Page: 39 / 55

Second Edition

First Printing

Operator's Manual

Inspections

Part No. 1261387

S-100HD • S-120HD

Inspection for Decals with
Symbols

Use the pictures on the next page to verify that all
decals are legible and in place.

Below is a numerical list with quantities and
descriptions.

Part No. Decal Description

Qty

27204

Arrow – Blue

27205

Arrow – Yellow

27206

Triangle – Blue

27207

Triangle – Yellow

28159

Label – Diesel

40434

Label – Lanyard Anchorage Points

52966

Cosmetic – 4 x 2

61227

Ground Control Panel

65266

Cosmetic – 4 x 4

65278

Caution – No Step

82240

Label – Noise Level

82472

Label – Crushing Hazard

82473

Label – Compartment Access

82481

Label – Battery/Charger Safety

82487

Label – Read the Manual

82547

Label – Maximum Capacity, 340 kg

82548

Label – Platform Rotate

82577

Label – Platform Overload Patch

82604

Label – Max Manual Force, 400 N

97757

Label – Hydraulic Oil Level

97815

Label – Lower Mid-rail

114112

Label – Transport Diagram

114249

Label – Tip-over Hazard, Tires

114251

Label – Explosion Hazard

114252

Label – Tip-over Hazard, Limit Switches

114473

Label – Tilt Alarm

133067

Label – Electrocution Hazard

133205

Label – Electrocution/Burn Hazard

215005

Label – Lifting Point

226144

Label – Emergency Stop, Platform
Controls

Part No. Decal Description

Qty

226145

Label – Boom Up/Down, Platform
Controls

226146

Label – Boom Extend/Retract & Swing
Rotate, Platform Controls

226147

Label – Steer/Drive, Platform Controls

1256293 Label – CG and Lifting Capacity

(S-100HD)

1256294 Label – CG and Lifting Capacity

(S-120HD)

1256298 Label – Wheel Load, S-100HD

1256299 Label – Wheel Load, S-120HD

1256300 Label – Range of Motion, S-100HD and

S-120HD

1256301 Cosmetic – Genie S-100HD

1256303 Cosmetic – Genie S-120HD

1256302 Cosmetic – S-100HD

1256304 Cosmetic – S-120HD

T110470 Label – Close Cover When Not Using

Platform Cotrols

T110549CS

Label – Fault Code Chart (China

Only)

T114286 Label – Install Cover/Read the Manual

T114471 Label – No Step or Ride

Summary of Contents for S-100HD
























































Search results

Summary of Contents for S-100HD

Reviews:

Related manuals for S-100HD

Brands by name

Popular brands

Genie S-100HD, Operator'S Manual

Search results

Summary of Contents for S-100HD

Reviews:

Related manuals for S-100HD

Brands by name

Popular brands