Genie S-100HD Operator'S Manual Download Page 37

Page: 37 / 55

Second Edition

First Printing

Operator's Manual

Inspections

Part No. 1261387

S-100HD • S-120HD

Test Drive Tilt Cutout

Press down the foot switch.

With the boom fully stowed, drive the machine
onto a slope where the chassis angle is greater
than 4.5° along the Y-Axis (front to back).

Result: The machine should continue to drive.

Return the machine to level ground and extend
the boom approximately 110 cm.

Drive the machine onto a slope where the
chassis angle is greater than 4.5° along the
Y-Axis (front to back).

Result: The machine should stop once the
machine reaches 4.5° of chassis tilt.

Retract the boom to the stowed position or
drive in the opposite direction.

Result: The machine should drive.

Return to level ground and raise the boom to
approximately 15° above horizontal.

Drive the machine onto a slope where the
chassis angle is greater than 4.5° along the
Y-Axis (front to back).

Result: The machine should stop once the
machine reaches 4.5° of chassis tilt.

Lower the boom to the stowed position or drive
in the opposite direction.

Result: The machine should drive.

Return to level ground and stow the boom.

Press down the foot switch.

With the boom fully stowed, drive the machine
onto a slope where the chassis angle is greater
than 4.5° along the X-Axis (side to side).

Result: The machine should continue to drive.

Return the machine to level ground and extend
the boom approximately 110 cm.

Drive the machine onto a slope where the
chassis angle is greater than 4.5° along the
X-Axis (side to side).

Result: The machine should stop once the
machine reaches 4.5° of chassis tilt.

Retract the boom to the stowed position or
drive in the opposite direction.

Result: The machine should drive.

Return to level ground and raise the boom to
approximately 15° above horizontal.

Drive the machine onto a slope where the
chassis angle is greater than 4.5° along the
X-Axis (side to side).

Result: The machine should stop once the
machine reaches 4.5° of chassis tilt.

Lower the boom to the stowed position or drive
in the opposite direction.

Result: The machine should drive.

Return to level ground and stow the boom.

Summary of Contents for S-100HD
























































Search results

Summary of Contents for S-100HD

Reviews:

Related manuals for S-100HD

Brands by name

Popular brands

Genie S-100HD, Operator'S Manual

Search results

Summary of Contents for S-100HD

Reviews:

Related manuals for S-100HD

Brands by name

Popular brands