September 2014
3 - 8
GTH-1048 • GTH-1056
Part No. 123701
Section 3 • Scheduled Maintenance Procedures
A-4
Lubricate the Boom
Genie specifications require that this procedure be
performed every 8 hours or daily, whichever
comes first.
Greasing the specified locations is essential for
good machine performance and service life.
Operating the machine with little or no grease
may cause the machine to perform poorly and
continued use could cause component damage.
1 Fully extend the boom. Raise the boom as
needed.
2 Lubricate the top and bottom boom tube wear
pads.
Note: Do not lubricate the side wear pads.
3 Return the boom to the stowed position.
Grease Specification
Chevron Ultra-duty grease, EP NLGI 2 (lithium based)
or equivalent
CHECKLIST
A
PROCEDURES
A-5
Perform Engine Maintenance -
All Models
Note: Engine specifications require that this
procedure be performed every 8 hours or daily,
whichever comes first.
Engine oil level - check
Coolant level - check/add
Fuel system filter/water separator - drain
Engine tightness - check or leaks
Exhaust system - check for leaks
Required maintenance procedures and additional
engine information is available in the
Perkins 1100D Operation and Maintenance
Manual (Perkins part number SEBU8172-00),
Perkins 1204 Operation and Maintenance Manual
(Perkins part number SEBU8605-01),
Deutz TCD3.6 Operation Manual
(Deutz part number 0312 3907),
OR the
John Deere 4045HF485 Operator's Manual
(John Deere part number OMRG36852).
Perkins 1100D Operation and Maintenance Manual
Genie part number
123702
Perkins 1204 Operation and Maintenance Manual
Genie part number
218726
Deutz TCD3.6 Operation Manual
Genie part number
218707
John Deere 4045HF485 Operator's Manual
Genie part number
123703
Summary of Contents for GTH-1048
