background image

IMPORTANT

SAFETY

INSTRUCTIONS

30

WARNING

To reduce the risk of 

severe injury or death:

TRANSMITTER

COMPLIANCE

STATEMENT

Transmitters comply with all United States and Canadian legal 
requirements as of the date of manufacture. No warranty is 
made that they comply with all legal requirements of any other 
jurisdiction. If transmitters are to be used in another country, 
the importer must determine compliance with any local laws 
and regulations which may differ from United States and 
Canadian requirements prior to use.

Los transmisores cumplen con todas las reglamentaciones 
legales de los Estados Unidos y del Canad , en la fecha de 
fabricaci n. Ninguna garant a se da que cumplan con todas las 
reglamentaciones legales de ninguna otra jurisdicci n. Si los 
transmisores se van a utilizar en otro pa s, el importador debe 
determinar si cumplen con las reglamentaciones y leyes 
locales que puedan ser diferentes a las reglamentaciones 
de los Estados Unidos y del Canad , antes de usar los mismos.

Sendeger te entsprechen allen gesetzlichen Bestimmungen in 
den USA und Kanada zum Zeitpunkt der Herstellung. Wir 

bernehmen keine Gew hrleistung f r die Einhaltung aller 

gesetzlichen Bestimmungen in anderen L ndern. Sollen 
Sendeger te in anderen L ndern eingesetzt werden, so muss 
der Importeur vor dem Gebrauch sicherstellen, dass die 
Sendeger te auch solchen lokalen Bestimmungen entsprechen, 
welche von den Bestimmungen der USA und 
Kanadas abweichen.

Les  metteurs sont conformes   la r glementation am ricaine 
et canadienne   compter de leur date de fabrication. Aucune 
garantie n est stipul e indiquant qu ils sont conformes   toutes 
les prescriptions juridiques d autres autorit s. Si les  metteurs 
sont utilis s dans d autres pays, il incombe   l importateur d en 
d terminer leur conformit  aux lois et r gles locales pouvant 
diff rer de celles des  tats-Unis et du Canada avant toute 
utilisation desdits  metteurs.

1

READ AND FOLLOW ALL 
INSTRUCTIONS.

2

Never let children operate or play with the 
Door Controls. Keep the Remote Control 
away from children.

3

Always keep the moving door in sight and 
away from people and objects until the 
door is completely closed. NO ONE 
SHOULD CROSS THE PATH OF THE 
MOVING DOOR.

4

NEVER GO UNDER A STOPPED, 
PARTIALLY OPEN DOOR.

5

Test Opener monthly. The door MUST 
reverse on contact with a 1-1/2" high 
object (or a 2" x 4" board laid flat) at the 
center of the doorway on the floor. After 
adjusting either the Force or the Limit of 
travel, retest the Door Opener. Failure to 
adjust the Opener properly may cause 
severe injury or death.

6

When possible use the Emergency 
Release only when the door is closed.
Use caution when using this Release with 
the door open. Weak or broken springs 
are capable of increasing the rate of door 
closure and increasing the risk of severe 
injury or death.

7

KEEP GARAGE DOORS PROPERLY 
BALANCED. See Owner's Manual. An 
improperly balanced door increases the 
risk of  severe injury or death. Have a 
Genie Factory Authorized Dealer make 
repairs to cables, spring assemblies, and 
other hardware.

8

SAVE THESE INSTRUCTIONS.

Summary of Contents for CM7600 Series




































Reviews: