background image

14

MAIN ASSEMBLY

FOR HELP-1.800.354.3643 OR GENIECOMPANY.COM

14. Attach emergency release knob, cord 

and tag.
• Tie an overhand knot in one end of 

emergency release cord [17].
– Slide cord through center of knob [18].

Fig. 1-17.

– Slide cord through hole in emergency 

release lever (on carriage).

– Tie a second knot in this end. Fig. 1-18.
– Slip wire of emergency release tag [19] 

through hole in emergency release lever 
and twist it around itself.

15. Attach limit switches.

• “CLOSE” limit switch [15B].

(Switches are identical.) 

– Place “CLOSE” limit switch over top of rail

about 12 inches from rail strap. Fig. 1-19.

– Check that white lever is toward 

power head.

– Insert set screw [16] into limit switch 

hand tight only to temporarily hold switch 
in place. Fig. 1-19A.

– Attach brown wire to switch. Fig. 1-19B.

– Leaving some slack in wire (Fig. 1-20), 

run wire down inside groove in top of rail 
back to power head.

– Use wire clip [44] to help maintain slack.

Fig. 1-20.

• “OPEN” limit switch [15A].

– Place “OPEN” limit switch over top of rail 

about 12 inches from power head. Fig. 1-21.

– Check that white lever is on side away from

power head. (This means limit switches 
hang off opposite sides of rail. Check this 
to help verify they are installed properly.)

– Insert set screw [16] into limit switch hand

tight only to temporarily hold switch in place.

– Attach grey wire to switch. Fig. 1-21.
– Leaving some slack in wire (Fig. 1-21), 

run wire down inside groove in top of rail 
back to power head.

– Use wire clip [44] to help maintain slack.

Fig. 1-21.

• Coil excess wire and tape it to top of power 

head. Fig. 1-21A.

Fig. 1-19

A

B

Fig. 1-20

wire clip

power head

Fig. 1-21

A

“close”

switch

“open”

switch

set screw

OPEN GREEN PARTS BAG

Screws for attaching light cover are included in this bag.

Please set aside for use later.

grey wire

brown wire

Fig. 1-17

Fig. 1-18

release

knob

tag

cord

#8-32 x 3/8" Hex head screw

Wire clip

[16]

[44]

Summary of Contents for CM7600 Series




































Reviews: