manualshive.com logo in svg

Generac Power Systems MGG155, Operating Manual

Share
Download
Generac Power Systems MGG155 Operating Manual Download Page 33

Operation

35319 C

MGG155/210 Operating Manual

27

Figure 12 - Generator Output Connections 

CUSTOMER CONVENIENCE RECEPTACLES

The unit is equipped with two 120V GFCI receptacles, located to the right of the customer connection box. These 
receptacles are not routed through the main circuit breaker. Each receptacle has its own circuit breaker, located 
directly above it.

Figure 13 - 120V GFCI Receptacles 

Power to the receptacles is available any time the generator is running, even if the main 
circuit breaker is OFF (O). 

VERIFY ANY EQUIPMENT CONNECTED TO THE CONVE-

NIENCE RECEPTACLES IS TURNED OFF BEFORE TURNING THE BREAKERS ON

 and 

the output voltage is correct for the equipment that is connected to the receptacles. Improper 

voltage may cause equipment damage, property damage, or malfunction.

1.   Connections lugs

2.   Bonding plate

00862

1

2

20A Circuit Breakers

GFCI Receptacles

02021

Discount-Equipment.com

Summary of Contents for MGG155




































































Reviews:

No comments

Brands by name

Popular brands

Load more brands